background image

Basic Installation Procedures

38

Freedom EX 4000 Installation Guide

Connecting to the RV-C Ports

The RV-C ports of the Freedom EX 4000 accepts a
corresponding standard patch cable with an RJ-45 (see 

Figure

27

) connector.

NOTE

: Do not connect the Sync cable to these ports if you are

stacking two units. The inverter will stop operating and generate
an event code 66 or 69. Remove the cable connections
immediately.

Figure 26 RV-C ports

1

+12_CAN

2

NC

3

GND

4

CAN1_RV-C_L

5

CAN1_RV-C_H

6

GND

7

+12_CAN

8

GND

Figure 27 RJ-45 connector pinouts/wire colors

1

+12_CAN

orange/white

2

NC

orange

3

GND

green/white

4

CAN1_RV-C_L

blue

5

CAN1_RV-C_H

blue/white

6

GND

green

7

+12_CAN

brown/white

8

GND

brown

Figure 28 RJ-45 network terminator

A

Use the supplied network
terminator (A) when the
Freedom EX 4000 is installed
as an end device in the CAN
network and also when
stacking two units together
(see

Figure 15 on page 29

and

Figure 13 on page 26

). Apply a

similar 120-ohm terminator to
the other end device in the
CAN network, if applicable.

Connecting to the USB Port

The USB port is reserved for firmware updates to the Freedom
EX 4000 and must not be used for powering and charging USB
devices.

Connecting to the Remote Port

The Freedom EX 4000 can accommodate the Remote panel
(PN: 808-0817-03, sold separately).

To connect the remote panel to the remote port:

1. Route and wind the cable two times through the ferrite

core (supplied with the remote panel) before extending the
connector to the port. The ferrite core has to be closest to
the Freedom EX 4000's RJ12 Remote port .

2. Plug the remote panel unit's cable connector to the RJ12

Remote port on the unit. For the location, see

Figure 22

on page 37

.

3. Plug the other connector to the Remote panel unit.

2x 

ferrite core

remote

cable

connector

NOTE

: When the remote panel is connected, turn the

inverter/charger/converter’s Power button to to Standby (up
position). This allows the remote panel to control the
inverter/charger/converter’s power status.

Содержание Freedom EX 4000





















































Отзывы: