Wood Stone FIRE DECK 6045 Скачать руководство пользователя страница 9

Страница: 9 / 44

Fire Deck

Service Manual

M0011.09 APRIL 2019

An ongoing program of product improvement may
require us to change specifications without notice.

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TOLL FREE

800.988.8103

TEL

360.650.1111

FAX

360.650.1166

E-MAIL

[email protected]

woodstone-corp.com

OPERATION SEQUENCE - RFG-IR

Note:

Ovens equipped with 2 Radiant Burners will have a third Valve, SV-3, which will be powered at the same time as the SV-2

Valve described above� The operation sequence is identical to that of SV-2� However, be aware that as long as SV-2 or
SV-3 lights, the Dome Flame indicator light will come on and the Controller will power SV-1 as necessary�

BURNER OPERATION SEQUENCES

RFG-IR OVENS - TOUCHPAD CONTROLLER

Pilot lights

Power On

SV-2 Valve powers Igniter and
opens Pilot Valve for radiant (side)
Burner�

Pilot does not light- SV-2 times
out�

SV-2 senses Pilot flame Igniter
off- SV-2 opens- Burner lights-
Dome flame indicator light
comes on�

Radiant Burner remains on until
oven is turned off�

Floor temperature above Hearth
Set Point- Controller does not
power SV-1 (Underfloor IR Burner)�

Floor Temperature below Hearth
Set Point- Controller sends power
to SV-1- SV-1 powers Igniter and
opens Pilot Valve�

Pilot lights- SV-1 senses Pilot
flame- Igniter off- SV-1 opens-
Underfloor Burner lights- Hearth
Heat light on�

Floor reaches the Hearth Set Point
temperature- Controller turns off
power to SV-1 and underfloor IR
Burner shuts off�

Pilot does not light- SV-1 times
out- Touchpad Controller flashes
“chec”�

Содержание FIRE DECK 6045













































Результаты поиска

Содержание FIRE DECK 6045

Отзывы:

Похожие инструкции для FIRE DECK 6045

Бренды по названию

Популярные бренды

Wood Stone FIRE DECK 6045, Руководство по обслуживанию

Результаты поиска

Содержание FIRE DECK 6045

Отзывы:

Похожие инструкции для FIRE DECK 6045

Бренды по названию

Популярные бренды