Wood Stone FIRE DECK 6045 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 44

background image

Fire Deck

Service Manual

PG

19

OF

44

M0011.09 APRIL 2019

An ongoing program of product improvement may
require us to change specifications without notice.

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TOLL FREE

800.988.8103

TEL

360.650.1111

FAX

360.650.1166

E-MAIL

[email protected]

woodstone-corp.com

RADIANT BURNER TROUBLESHOOTING

Flame height is low� The flame
should be approximately 12–15
inches tall at full-throttle�

1.

The Burner gas pressure is low; adjust the regulator on the Gas Valve to obtain
the specified pressure� If the specified pressure cannot be obtained, verify
that incoming gas pressure is sufficient; check this with the oven running� If
the incoming pressure is good, there may be a blockage in the throttle control
valve� Disassemble and clean the Valve; see Common Repair Procedures
section of this manual�

2.

Debris in the Burner� Remove and clean� See Common Repair Procedures
section of this manual�

Soot is forming near the Burner�

Note:

Do not run oven with Night Heat

Retention doors in place�

1.

Some sooting is normal when the oven is cold� This will burn away when the
oven reaches operating temperature�

2.

Check for debris in the Burner; remove Burner and clean� See the Common
Repair Procedures section� If a log set is installed, verify that it is positioned
correctly�

3.

If Burner is clean, check that the oven is properly configured for the gas being
supplied� Call Wood Stone�

Burner doesn’t light or goes out, and
the Igniter wires are burned�

1.

Loose Pilot Tube, tighten and replace Igniter

2.

Inadequate venting or negative air� See Installation and Operation Manual
instructions�

Radiant flame height is much higher on
the Igniter side of the Burner� The flame
on this side does not decrease when
the operator turns down the flame�

Pilot orifice is damaged or missing� Remove Pilot/Igniter� Orifice fits between the
brass Compression fitting attaching the Pilot Tube and the Igniter body� Replace with
new Pilot orifice�

Symptom

Probable Cause/Solution

«
...
17
18
19
20
21
...
»

Содержание FIRE DECK 6045













































Отзывы:

Нет отзывов

Похожие инструкции для FIRE DECK 6045

Бренд: Magic Vac Страницы: 72

Бренд: PALSON Страницы: 1

Бренд: PALSON Страницы: 28

Бренд: MiLAN Страницы: 36

Бренд: SALCO Страницы: 23

Бренд: ohmex Страницы: 76

Бренд: Omcan Страницы: 8

Бренд: Metcalfe Страницы: 20

Design Multicook PLUS

Бренд: Gastroback Страницы: 80

Бренд: Waring Страницы: 7

vinopazzo VPC27SS2

Бренд: AVG Страницы: 26

Бренд: SOLIS Страницы: 76

Design Dorrautomat Natural Plus

Бренд: Gastroback Страницы: 52

Classic Deluxe 90 Dual Fuel

Бренд: Falcon Страницы: 44

Бренд: NuWave Страницы: 100

Бренд: Revolution Страницы: 28

Бренд: True Страницы: 2

Бренд: German pool Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды