Wood Stone FIRE DECK 6045 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 44

background image

Fire Deck

Service Manual

PG

14

OF

44

M0011.09 APRIL 2019

An ongoing program of product improvement may
require us to change specifications without notice.

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TOLL FREE

800.988.8103

TEL

360.650.1111

FAX

360.650.1166

E-MAIL

[email protected]

woodstone-corp.com

CONTROLLER TROUBLESHOOTING

RFG-IR oven

: Controller is on, but dome flame

does not come on�

RFG oven

: Controller is on, but dome flame is

not coming on�

W-IR oven:

Controller is on but IR is not

coming on�

Controller is fine, See Radiant and Infrared Burner Troubleshooting section
of this manual�

Note:

On RF-IR ovens with 2 Radiant Burners (dome flame), the Controller

will not signal the Infrared Burner to light until at least 1 of the Radiant
Burners has lit�

RFG-IR Oven

: Dome flame comes on, a short

time later the display flashes “check” and the
Hearth Heat Indicator Light flashes�

Controller is fine� It is indicating that the Controller called for IR heat, but
the IR Burner did not fire within the time allowed by the Controller� See
Radiant and Infrared Burner Troubleshooting section of this manual�

9690 RFG-IR Oven:

Display is on, no Burners

are lighting and Hearth Temperature is above
800 °F�

9690 RFG-IR Oven:

All Burners go out, display

remains lit, Hearth Temperature is above
800 °F�

9690 RFG-IR Oven:

No Burners are lit, Hearth

Temperature is below 800 °F�

Older 9690 models incorporate an over-temperature control that shuts off
power to the Gas Valves� Once the oven floor temperature has dropped
below 800 °F, it may be reset by turning the oven off and then back on� If
equipped the overtemp module is located in the right side junction box on
the Transformer Plate below the oven at the rear�

Product is overcooking and the floor
temperature is higher than the Hearth Set
Point� The IR Burner should not be running�

Operational problem.

The operator is leaving the radiant flame at

too high a setting for too long and as a result, is driving up the oven
temperature through the use of too high a radiant flame� It is very easy
for a radiant flame to heat the oven’s hearth temperature well above the
Hearth Set Point if it is not managed correctly (especially if the oven is not
under much use at the time)� Call Wood Stone for operational assistance�

Product is overcooking and the Controller
is displaying a hearth temperature that is
considerably lower than the Hearth Set Point
and the IR Burner is running�

1.

Thermocouple may be shorted, causing it to read the temperature at the
point of the short� Look for damage to the Thermocouple wire�

2.

Operational problem� Contact Wood Stone�

Symptom

Probable Cause/Solution

«
...
12
13
14
15
16
...
»

Содержание FIRE DECK 6045













































Отзывы:

Нет отзывов

Похожие инструкции для FIRE DECK 6045

Бренд: U-Line Страницы: 47

Бренд: Logik Страницы: 12

Бренд: Cook's Companion Страницы: 3

Бренд: Russell Hobbs Страницы: 7

Бренд: Sunnydaze Страницы: 11

Бренд: Weston Страницы: 24

Бренд: PAC FOOD Страницы: 18

Бренд: Brice Страницы: 14

Бренд: Inkbird Страницы: 75

Бренд: inventum Страницы: 48

Бренд: Salton Страницы: 15

Бренд: Zelmer Страницы: 23

Design Advanced Professional 46016

Бренд: Gastroback Страницы: 60

Бренд: SEVERIN Страницы: 54

Бренд: ARESA Страницы: 18

Бренд: ARESA Страницы: 22

Бренд: ARENDO Страницы: 80

Feeding Bowl/Plate

Бренд: Tupperware Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды