Wood Stone FIRE DECK 6045 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 44

background image

Fire Deck

Service Manual

PG

12

OF

44

M0011.09 APRIL 2019

An ongoing program of product improvement may
require us to change specifications without notice.

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TOLL FREE

800.988.8103

TEL

360.650.1111

FAX

360.650.1166

E-MAIL

[email protected]

woodstone-corp.com

GAS OVEN COMPONENTS

INFRARED BURNER ASSEMBLY

This is the Burner located beneath the floor of the oven�
The tubes on the outside of the Burner are used to supply
air to the Burner� You will not see flame in these tubes�

DO NOT ATTEMPT TO LIGHT THIS BURNER MANUALLY!

To visually verify that the Burner is running, look through
the gap next to the Pilot assembly and you should see a
reddish glow over the ceramic Burner elements� This Burner
operates only when the hearth temperature is lower than
the Controller’s Hearth Set Point�

THERMOCOUPLE

A Type K Thermocouple is used to sense the temperature of the oven floor (hearth),
about 1 inch beneath the hearth surface� It is located slightly to the rear of the center
of the oven (behind the IR on an IR equipped oven)� It is embedded in the floor of the
oven, but is easily replaceable� Older 9690 models only are equipped with a second
calibrated Thermocouple for the overtemp module�

SV1 AND SV2 WIRE HARNESSES

These harnesses supply the voltage needed to activate and power the ignition system
on the respective Valves� They also send flame verification voltage from the Valve back
to the Controller�

HEAT SHIELD

The Heat Shield (on models FD-6045 and FD-8645) helps the oven retain heat�
A pulley and counterweight system enables the Heat Shield to remain in the open
position to allow easy access for moving product in and out of the oven� A special
high temperature glass is used in the Heat Shield� If the glass becomes broken or
damaged, replace only with glass supplied by Wood Stone�

Pulley/counterweight system

CONTROLLER WIRE HARNESS

This harness carries low voltage to and from the oven Controller� It also contains the
Thermocouple wires�

Heat Shield

«
...
10
11
12
13
14
...
»

Содержание FIRE DECK 6045













































Отзывы:

Нет отзывов

Похожие инструкции для FIRE DECK 6045

Бренд: Hamilton Beach Commercial Страницы: 8

Бренд: Xo Страницы: 24

Бренд: Adler Europe Страницы: 68

Бренд: Ugolini Страницы: 56

milkloud 300777

Бренд: ARENDO Страницы: 33

Бренд: Sinbo Страницы: 55

Бренд: CellarCool Страницы: 63

Бренд: True Страницы: 1

FoodSaver VAC700

Бренд: Sunbeam Страницы: 24

Бренд: Waring Страницы: 44

Бренд: Cremesso Страницы: 44

Бренд: R.G.V. Страницы: 48

Бренд: RUSTA Страницы: 36

Бренд: Indesit Страницы: 34

BEVERAGE CENTER

Бренд: Jenn-Air Страницы: 32

Бренд: Conair Страницы: 2

Бренд: Fontana Forni Страницы: 16

Бренд: PROMARKS Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды