Wood Stone FIRE DECK 6045 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 44

background image

Fire Deck

Service Manual

PG

25

OF

44

M0011.09 APRIL 2019

An ongoing program of product improvement may
require us to change specifications without notice.

WOOD STONE CORPORATION

1801 W. Bakerview Rd.
Bellingham, WA 98226 USA

TOLL FREE

800.988.8103

TEL

360.650.1111

FAX

360.650.1166

E-MAIL

[email protected]

woodstone-corp.com

COMMON REPAIR PROCEDURES

HEAT SHIELD CABLE REPLACEMENT

Please refer to the diagram below� If a cable has failed, Wood Stone recommends that you replace both cables�

1.

Remove the screws that attach the counterweight covers�

2.

Raise the Heat Shield up several inches and block it up� A short piece of 2x4 or anything similar works well for this� Place a block
under the counterweight as well to relieve the tension on the cable�

3.

Tilt the door forward� Where the cable attaches to the Heat Shield, note the position of the spacer and how the crimp of the cable
eyelet is oriented towards the center of the oven� On one side of the Heat Shield only, use a 3/16" Allen wrench to remove the
cable� Position the Heat Shield so it will not fall or be damaged and proceed with Step 4�

4.

Continuing on the same side, remove the 9/16" nut that attaches the cable to the counterweight�

5.

Continuing on the same side, remove the four Phillips screws that hold the pulley block in place� Remove the pulley block and
cable�

6.

Remove the “C” clip on the pulley block, and remove the pulley� Slide the new cable over the pulley and reinstall the pulley into the
pulley block� Reinstall the pulley block as it was before�

7.

Attach the cable eyelet to the counterweight using the 9/16" nut removed in Step 4�

8.

Attach the cable eyelet to the Heat Shield using the Allen head shoulder bolt and spacer removed in Step 3�

The eyelet should be installed between the spacer and the head of the bolt, with the cable crimp oriented towards the
center of the oven, overhanging the spacer.

9.

Repeat steps 3–8 for the cable on the opposite side�

Cable connects to

Heat Shield here

Cable

Pulley block

(cutaway view)

Counterweight

Heat Shield

«
...
23
24
25
26
27
...
»

Содержание FIRE DECK 6045













































Отзывы:

Нет отзывов

Похожие инструкции для FIRE DECK 6045

Бренд: Victory Страницы: 2

Бренд: Cosori Страницы: 28

Бренд: Flama Страницы: 24

2.0 K400 SERIES

Бренд: Keurig Страницы: 11

Бренд: Gold Medal Страницы: 32

Бренд: Metcalfe Страницы: 16

Бренд: P&C Страницы: 3

Бренд: Star Страницы: 24

Бренд: icetro Страницы: 36

Бренд: Gast Страницы: 17

Бренд: Wolfgang Puck Страницы: 14

Бренд: True Страницы: 2

Бренд: John Lewis Страницы: 24

Bistro BECP0020

Бренд: Wolfgang Puck Страницы: 18

Бренд: Aroma Professional Страницы: 104

Бренд: Celme Страницы: 40

COURANT CSD-2176

Бренд: Impecca Страницы: 33

Бренд: ADE Страницы: 88

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды