WhisperGen PPS16-12MD Скачать руководство пользователя страница 78

Страница: 78 / 84

Correcting Warnings

Trouble Shooting

Code

Likely Cause and Recommended Action

102

Likely cause:

Exhaust gas hotter than normal, possibly due to low engine gas pressure.

Recommended Action:

Attempt to restart. Contact an authorised WhisperGen

service agent if the problem reoccurs.

104

Likely cause:

Engine coolant hotter than normal.

Recommended Action:

Check coolant level. Check coolant and seawater circuits for obstructions. Check pumps for operation.

107

Likely cause:

Temperature in electronics enclosure abnormally high.

Recommended Action:

Ensure ambient temperature is below 40°C. Ensure airflow from the base of the enclosure through to the
electronics heat sink is not blocked. Ensure the enclosure lid is fitted and well sealed

126

Likely cause:

Controller is reset while engine is running or engine is hot. This could be the result of a bad contact between
the WhisperGen

and the control panel.

Recommended Action:

Fit a new cable.

135

Likely cause:

Low battery bank voltage.

Recommended Action:

Check battery bank connections and battery bank voltage sensing wires. Set a higher value for

Max Run

Hours

and/or turn

Auto-charge

option

182

Likely cause:

Excessive voltage drop in cabling to battery bank.

Recommended Action:

Check battery bank connections and cables.

183

Likely cause:

Battery bank temperature is high.

Recommended Action:

Check battery bank connections and ventilate battery bank compartment.

190

Likely cause:

Battery bank voltage is unstable during charging.

Recommended Action:

Check battery bank connections and cables.

195

Likely cause:

Battery bank is discharged below a preset level.

Recommended Action:

Start the WhisperGen

if it is not operating. Reduce electrical load on the battery bank. Set a higher value for

Max Run Hours

and/or turn

Auto-charge

option

Содержание PPS16-12MD





















































































Результаты поиска

Содержание PPS16-12MD

Отзывы:

Похожие инструкции для PPS16-12MD

Бренды по названию

Популярные бренды

WhisperGen PPS16-12MD, Руководство пользователя

Результаты поиска

Содержание PPS16-12MD

Отзывы:

Похожие инструкции для PPS16-12MD

Бренды по названию

Популярные бренды