WhisperGen PPS16-12MD Скачать руководство пользователя страница 59

Страница: 59 / 84

Maintenance

Replacing Fuses

Replacing Other Fuses

Overview

The WhisperGen

has fuses that protect against overloading of its

electrical circuits. If a circuit is overloaded, the fuse will blow and the
WhisperGen

will shut down with the fault indicated on the control panel.

Before replacing a fuse, find out the cause of the fault.

Otherwise, damage to equipment may occur. If you are unsure of the cause
of the fault, contact your authorised WhisperGen

service agent for

assistance.

To prevent unintentional starts of the WhisperGen

, heed the

warning given at the beginning of this section.

Do not touch surfaces that are labelled as hot

Ensure that the replacement fuse is of a similar type and of the

correct current rating.

It is advisable to keep spare fuses with the WhisperGen

at all

times.

Procedure

To replace a fuse (other than the battery bank voltage fuse):

1. Stop

the

WhisperGen

and wait until the

STANDBY

indicator on the

control panel is lit. Then remove the enclosure lid.

2. Disconnect

the

WhisperGen

from the battery bank by opening the

circuit breaker.

3. Release the four screws securing the cover of the electronics

enclosure and remove the cover.

FUEL

OFF

Electronics
Enclosure
Cover

Содержание PPS16-12MD





















































































Результаты поиска

Содержание PPS16-12MD

Отзывы:

Похожие инструкции для PPS16-12MD

Бренды по названию

Популярные бренды

WhisperGen PPS16-12MD, Руководство пользователя

Результаты поиска

Содержание PPS16-12MD

Отзывы:

Похожие инструкции для PPS16-12MD

Бренды по названию

Популярные бренды