WhisperGen PPS16-12MD Скачать руководство пользователя страница 56

Страница: 56 / 84

Checking Battery Bank Connections

Maintenance

Checking Battery Bank Connections

Overview

Power flows between the WhisperGen

and battery bank via two power

cables connected to the terminals of the battery bank. The WhisperGen

also monitors the battery bank voltage, current, and temperature via
electrical wires connected to the battery bank.

If an electrical fault or warning occurs, you may need to check these
electrical connections. Refer to the Trouble Shooting section in the User
Manual.

Do not touch the surfaces that are labelled as hot.

If stopping the WhisperGen

to re-secure a wire/cable, heed the

warning given at the beginning of this section to prevent unintentional starts
of the WhisperGen

Procedure

To check the battery bank connections:

1. Access the battery bank managed by the WhisperGen

, and ensure

that the battery bank connections, as shown below, are intact and
clean.

F UE L

OF F

Current Shunt

Current Sensing
Wires

Power Cables

Voltage Fuse

White

No assigned colour

Green

Black

Violet

Red

Circuit
Breaker

Voltage
Sensing
Wires

Temperature
Sensor

Battery Bank

WTL0032

Personal Power Station

2. Check that the circuit breaker is closed.

3. Replace the voltage fuse if it has blown.

4. Check that the electrical insulation of the wires/cables is intact.

5. Remove the enclosure lid.

6. Check that the electrical connections on the side of the electronics

enclosure, as shown below, are intact. Before re-securing a wire/cable,
first stop the WhisperGen

and disconnect it from the battery bank by

opening the circuit breaker.

FUEL

OFF

Green

White

Red

Black

Violet

Current Sensing
Wires

Power Cables
(No Assigned Colour)

Voltage Sensing
Wires

Temperature
Sensing Wires

9
1

2
1

3
1

5
1

6
1

234

7. Replace the enclosure lid. If you had disconnected the WhisperGen

from the battery bank, reconnect it by closing the circuit breaker.

Содержание PPS16-12MD





















































































Результаты поиска

Содержание PPS16-12MD

Отзывы:

Похожие инструкции для PPS16-12MD

Бренды по названию

Популярные бренды

WhisperGen PPS16-12MD, Руководство пользователя

Результаты поиска

Содержание PPS16-12MD

Отзывы:

Похожие инструкции для PPS16-12MD

Бренды по названию

Популярные бренды