WhisperGen PPS16-12MD Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 84

background image

Operation

Displaying System Information

33

Extra Info Menu

Extra Info Menu

Parameter

Meaning

Typical Range

Alt Current

The electric current in Amperes that is being
generated by the WhisperGen

TM

alternator. Positive

values indicate current generation and negative
values indicate current flow to the WhisperGen

TM

from the battery bank during cranking.

12V: -20 to 75A.

24V: -10 to 37A.

Air %

The power applied to the air blower as a
percentage of the maximum power that can be
applied to it. The higher the air flow rate, the higher
the combustion rate.

0 to 100%.

Bus Voltage

The voltage across the electrical terminals of the
WhisperGen

TM

.

12V: 10 to 15.5V.

24V: 20 to 31V.

Coolant Temp

The temperature in °C of the coolant. The coolant
temperature reflects the temperature of the engine
block.

-10 to 85°C.

Clamp Current

The excess electric current in Amperes being
diverted into the "clamp", an electric water heating
element located inside the WhisperGen

TM

enclosure.

0 to 70A.

Clamp Voltage

The voltage setting of the "clamp" system.

12V: 12.2 to 16.3V.

24V: 24.85 to 32.7V.

Exhaust Temp

The temperature in °C of exhaust gases between
the burner and exhaust heat exchanger.

-10 to 550°C.

FID Current uA

The current in µA flowing between the FID (flame-
ionisation detector) electrode and the burner shell.
A large current indicates a good stable flame in the
burner and correct FID operation.

0 to 10µA.

Fuel Cut Off

The position of the automatic fuel isolation valve
located inside the WhisperGen

TM

. It should be ON

when the WhisperGen

TM

is operating.

ON or OFF.

Fuel Metering

The operating state of the fuel pump. It should be
ON when the WhisperGen

TM

is operating.

ON or OFF.

Fuel Frequency

The rate at which fuel is pulsed into the burner. The
fuel pulse rate is adjusted in relation to power
demand and the air/fuel ratio.

2 to 16Hz

Glow Plug

The operating state of the glow plug. The glow plug
is turned ON as required during the start-up of the
burner.

ON or OFF.

Isolate Relay

The position of the main electrical isolator relay
located inside the WhisperGen

TM

. It should be ON

when the WhisperGen

TM

is operating.

ON or OFF.

Power Relay

The power supply to ancillary components such as
the fuel pump, coolant pump, etc. The power supply
should be ON when the WhisperGen

TM

is operating.

ON or OFF.

O2 Value

The quantity of oxygen in the exhaust. This reflects
the air/fuel ratio.

200 to 2500.

O2 Ave Error

The averaged difference between the air/fuel ratio
set point and the actual ratio. The smaller the
difference, the more stable the burner.

2 to 400.

Software Ver

The version of software the WhisperGen

TM

is

operating on.

A five-digit number.

«
...
39
40
41
42
43
...
»

Содержание PPS16-12MD





















































































Отзывы:

Нет отзывов

Похожие инструкции для PPS16-12MD

Бренд: 3onedata Страницы: 3

Бренд: 3onedata Страницы: 9

Бренд: 3onedata Страницы: 3

Бренд: 3onedata Страницы: 3

Бренд: 3onedata Страницы: 3

Бренд: 3onedata Страницы: 3

Бренд: 3onedata Страницы: 7

Бренд: Barco Страницы: 2

Zeverlution 3680

Бренд: Zeversolar Страницы: 2

Бренд: Kramer Страницы: 15

Бренд: PEAK COMMUNICATIONS Страницы: 18

Бренд: Lindy Страницы: 2

Бренд: Envertech Страницы: 2

Бренд: T+A Elektroakustik Страницы: 60

Бренд: Sonnen Страницы: 5

Бренд: Audio Technica Страницы: 11

Бренд: Kramer Страницы: 25

Бренд: Epcom Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды