WhisperGen PPS16-12MD Скачать руководство пользователя страница 79

Страница: 79 / 84

Resetting the WhisperGen

Resetting the Control Panel

Resetting the WhisperGen

Resetting the Control Panel

Due to unusual circumstances, the control panel may sometimes display an
incoherent message. If this happens, the control panel should be reset.

When performing trouble shooting tasks on the WhisperGen

refer to the applicable sections(s) when removing or replacing parts.

To reset the control panel:

•

Hold

down

Left Arrow

for at least six seconds. A beep will be heard

and the control panel will return to the default display, indicating normal
operation.

Battery Watts

Resetting the Electronics Hardware

Overview

In some cases, extreme electrostatic interference may cause the
WhisperGen

to become unresponsive to key presses on the control

panel. If this happens, the WhisperGen

electronics hardware should be

reset as soon as possible to ensure that the battery bank is kept charged.

Do not touch the surfaces that are labelled "Hot Surface".

Ensure that the replacement fuse is of a similar type and of the

correct current rating.

Procedure

To reset the WhisperGen

electronics hardware:

1. Remove the enclosure lid.

2. Remove the four screws in front of the electronics enclosure. Then

remove the electronics enclosure cover.

FUEL

OFF

Electronics
Enclosure
Cover

Содержание PPS16-12MD





















































































Результаты поиска

Содержание PPS16-12MD

Отзывы:

Похожие инструкции для PPS16-12MD

Бренды по названию

Популярные бренды

WhisperGen PPS16-12MD, Руководство пользователя

Результаты поиска

Содержание PPS16-12MD

Отзывы:

Похожие инструкции для PPS16-12MD

Бренды по названию

Популярные бренды