WhisperGen PPS16-12MD Скачать руководство пользователя страница 67

Страница: 67 / 84

Maintenance

Replacing the Evaporator Wick

11. Place the evaporator sleeve on the evaporator body.

12. Place the evaporator gasket on the evaporator, ensuring that all the

holes line up.

13. Insert the evaporator with the gasket into the burner and secure the

four screws.

14. Check that the FID slides freely into the burner. Readjust the

positioning of the evaporator as needed.

15. Refit the glow plug. Replace the glow plug if badly worn or damaged to

ensure optimal running.

16. Reconnect the fuel line to the evaporator. Finger tighten the nut then

tighten 3/4 turn using a spanner. Ensure that there is no leakage.

17. Refit the FID. Carefully the procedure in this manual entitled Replacing

the FID to ensure correct FID positioning for optimal running.

18. Replace the enclosure lid.

19. Turn on the WhisperGen

fuel valve.

The WhisperGen

may now be started as required.

Содержание PPS16-12MD





















































































Результаты поиска

Содержание PPS16-12MD

Отзывы:

Похожие инструкции для PPS16-12MD

Бренды по названию

Популярные бренды

WhisperGen PPS16-12MD, Руководство пользователя

Результаты поиска

Содержание PPS16-12MD

Отзывы:

Похожие инструкции для PPS16-12MD

Бренды по названию

Популярные бренды