WEISS WSG 32 Скачать руководство пользователя страница 37

Страница: 37 / 53

- 35 -

RELEASING

The gripper is opening

The gripped part is being released, the fingers are moving.

POSITIONING

Pre-positioning

The grippers are being pre-positioned and the fingers are moving.

ERROR

Error

An error occurred carrying out the last command. For errors which require

acknowledgment, the SF_FAST_STOP flag is also set in the system status

word. After any acknowledgment required, the movement can be restarted.



The gripper state does not indicate whether the gripper is referenced or not. Instead, the system

state flags (SF_REFERENCED) must be read to check this.

The state of the gripper is shown like the status word in the side bar of the web interface, see Figure 22.

The diagram in Figure 23 shows the possible transitions between the module’s states.

IDLE

PART LOST

NO PART FOUND

RELEASING

POSITIONING

ERROR

Pre-positioning

command

Grasp

command

Position
reached

Part detected and

grasping force

established

No part detected at

given width and within

clamping range

GRASPING

Release

command

Release width reached

Part was

lost/removed
while holding

Release

command

Release

command

HOLDING

Fast Stop

Acknowledge

command

Error during

command execution

occurred

Stop command:

Issuing a Stop command in any state (except ERROR) will abort the current action and immediately return to IDLE state.

Figure 23: Transitions between the grasping states

Содержание WSG 32






















































Результаты поиска

Содержание WSG 32

Отзывы:

Похожие инструкции для WSG 32

Бренды по названию

Популярные бренды

WEISS WSG 32, Инструкция по монтажу и эксплуатации

Результаты поиска

Содержание WSG 32

Отзывы:

Похожие инструкции для WSG 32

Бренды по названию

Популярные бренды