Weathermatic SmartWire 9600TW Скачать руководство пользователя

Страница: 28 / 48

http://support.weathermatic.com

10.0 Advanced Menu

10.3.2 SLW

10.3.2.1 LASTCOM

This feature records time elapsed since last successful

communication between the weather station and control panel.

10.3.2.2 BATTERY

Check the battery status in your wireless weather station here.

10.3.3 NEXT RUN

NEXT RUN is the total amount of run time SMART has calculated

for each zone based on ET deficits and SMART system audit

information entered on the SMART side of the dial. NEXT RUN

is calculated and revised each night at midnight 365 days per

year. The cumulative run time will carry forward until the next

scheduled watering cycle. NEXT RUN times will return to zero

aer each watering cycle. To review NEXT RUN, turn the dial to

Advanced Menu. Use the UP arrow button to access Review

and then use the NEXT and BACK buttons to scroll through the

zones.

10.3.4 RUN/SOAK

This feature allows the user to review expected Run/Soak

schedules that will occur when the controller is in the SMART

mode. Turn the dial to Advanced Menu. Use the UP button to

go to REVIEW and press the NEXT button. Use the UP button

to advance to RUN/SOAK. Press the NEXT button and zone 01

will show in the display. Press NEXT again and RUN with a time

will show. This is the maximum RUN time the controller can do

in SMART before going to SOAK. Press NEXT again and SOAK

will show in the display with a time. This is the minimum time the

zone must soak before it is ready to run again. SMART Run/Soak

times can be changed by adjusting the soil and slope settings

at SOIL TYPE on the programming dial. The times are also

affected by adjusting the SPRINKLER TYPE setting on the dial

for precipitation rate.

10.3.5 DEFICIT

Deficit is the amount of water (displayed in inches) that needs

to be replaced for your plant material due to water loss through

evapotranspiration – evaporation from soil and transpiration

from plants. Your SmartLine® controller will calculate the water

deficit each day at 11:50 pm based on data communicated to

it by the SLW series Weather Sensor. The water deficit will

continue to accumulate until the next scheduled watering cycle

and will return to a zero reading when watering is finished. The

SmartLine controller uses an internationally recognized formula

called the Hargreaves formula for calculating evapotranspiration.

During a rain event, deficits will decrease to zero. SmartLine

will not begin calculating deficits and run times again until the

ACTIVE LED goes back to green aer the SLW DLY.

If you wish to reduce the deficit numbers, press and hold down

either the UP or DOWN button for 5 seconds. This allows you to

use the DOWN button to reduce the latest deficit for the zone to

as low as 0 inches.

Deficit is only available for review when you are using SMART

mode.

10.3.6 FLOW

Your controller MUST have a flow compatible accessory in

order to monitor flow. This menu allows for setting up flow

monitoring’s pulse per gallons unit of measure. You will also

access the information for high flow peak, low flow peak, total

volume of flow per zone and the ability to clear the monitored

values.

Содержание SmartWire 9600TW

















































Результаты поиска

Содержание SmartWire 9600TW

Отзывы:

Похожие инструкции для SmartWire 9600TW

Бренды по названию

Популярные бренды

Weathermatic SmartWire 9600TW, Руководство пользователя

Результаты поиска

Содержание SmartWire 9600TW

Отзывы:

Похожие инструкции для SmartWire 9600TW

Бренды по названию

Популярные бренды