Weathermatic SmartWire 9600TW Скачать руководство пользователя

Страница: 40 / 48

http://support.weathermatic.com

14.0 Special System Features

• A unique address is configured in each decoder during the

configuration process.

• Valves are actuated by a command from the decoder.

• Diagnostic features—The SL9600TW reports failing solenoids.

• If a solenoid has failed, the decoder senses an open circuit

and/or over current condition and shuts down the valve.

• Each decoder will shut down if communication is lost to the

SLM48DM decoder module in the SmartLine® controller.

• Valves can be located up to 100 feet from the decoder.

• Decoder electronics are potted in chemical and waterproof

compounds for impervious protection from moisture and dirt.

15.0 Electrical Specifications

• Input voltage 24 - 28 VAC over the 2-wire system.

• The Weathermatic SL9600TW can support a total of 96

valves plus 2 master valves. A maximum of 5 valves including

master valve or pump relay can be operated concurrently.

• No electrical contact with soil.

• Shock resistant.

• Freeze/heat resistant (-20° to 60° C).

• All connecting wires are 14 gauge coated PVC and must be

installed with industry standard waterproof connectors such

as the 3M DBY or DBR.

Содержание SmartWire 9600TW

















































Результаты поиска

Содержание SmartWire 9600TW

Отзывы:

Похожие инструкции для SmartWire 9600TW

Бренды по названию

Популярные бренды

Weathermatic SmartWire 9600TW, Руководство пользователя

Результаты поиска

Содержание SmartWire 9600TW

Отзывы:

Похожие инструкции для SmartWire 9600TW

Бренды по названию

Популярные бренды