Weathermatic SmartWire 9600TW Скачать руководство пользователя

Страница: 13 / 48

http://support.weathermatic.com

4.0 Lightning Protection

1 Station

To SLM48DM

SLCONN

Waterproof

wiring connector

Common

Wire

2 Station

4 Station

Common

Wire

4.0 Lightning Protection

Weathermatic SLGDT gas discharge tube lightning arrestors

must be used on all 2-wire grids. The SLGDT lightning arrestor

attaches directly to the 2-wire system and helps dissipate

static electricity generated by a nearby lightning strike. While

Weathermatic components have lightning arresting features,

the SLGDT provides an extra measure of protection.

4.1 SLGDT Lightning Arrestor Features

• Protects the 2-wire system from excessive static charges

created by a lightning strike.

• Sealed and impervious to moisture, salts, fertilizers and mild

chemicals. Can be buried directly in the soil.

• Shock resistant

• Freeze/heat resistant (-20° to 60° C)

• No electrical contact with the soil

• Each Lightning Arrestor protects a 300 foot radius

4.2 Electrical Specifications

• Requires no power from the 2-wire system

• Can only be connected to SmartWire™ 2-wire systems

4.3 Installating the SLGDT Lightning Arrestor

1. Connect the RED and BLACK lead wires to the 2-wire system

RED and BLACK wires.

2. Attach the GREEN ground wire to Earth Ground (Grounding

Requirements below)

SL9600TW

Decode
Lightning Arrestor
2-Wire Path

600’ Max

50’ Max

Содержание SmartWire 9600TW

















































Результаты поиска

Содержание SmartWire 9600TW

Отзывы:

Похожие инструкции для SmartWire 9600TW

Бренды по названию

Популярные бренды

Weathermatic SmartWire 9600TW, Руководство пользователя

Результаты поиска

Содержание SmartWire 9600TW

Отзывы:

Похожие инструкции для SmartWire 9600TW

Бренды по названию

Популярные бренды