Weathermatic SmartWire 9600TW Скачать руководство пользователя

Страница: 16 / 48

http://support.weathermatic.com

7.0 Programming the SL9600TW Controller

6.1 Decoder Programming Steps

• Use the SL9600TW module mode button to select the PGM

programming position.

• Insert the RED and BLACK wires on the decoder in the

Programming Ports on the SL9600TW (RED to RED, BLACK

to BLACK).

• Use up/down arrow buttons to select the zone number to be

programmed.

• Push Program Status button to select the zone showing

in the display window. Note: When you are programming

a multi-valve decoder, the display will only show the zone

number for the first zone to be assigned to that decoder. The

remaining zones in the decoder are automatically assigned in

sequential numerical order.

• A GREEN status light will confirm your selection.

• If programming is not successful, a RED status light will

flash and an error code will be shown on the display. See

Troubleshooting for description of error codes.

• Mark the zone number programmed on the decoder. Note: If

you are using a multi-valve decoder, the decoder will record

the zone selected in the order previously noted for wire

colors. For example, if you are using the 4-valve decoder,

the first zone programmed will be Orange, the second

Yellow and so on. Mark the zone number on the decoder for

reference during field installation. You should also mark all

zone numbers on your valve layout plan for reference during

installation of the decoders.

7.0 Programming the SL9600TW Controller

Your SmartLine® controller has two operating modes: BASIC

mode or Weathermatic’s patented SMART mode. The BASIC

mode uses user assigned zone run times. The SMART mode

overrides user assigned zone run times and calculates zone

run times based on the location of the site, inputs by zone, and

weather readings from the SLW Weather Sensor. Note: SMART

requires the optional SLW Weather Sensor.

Smart watering calculates ET (evapotranspiration), the

landscape’s daily water loss, and schedules the correct amount

of irrigation to replace the loss. When combined with a

Weathermatic SLW Weather Sensor, Smart mode gives you the

power to reduce water waste. Many water districts are offering

rebates for Smart mode users. Check with your local district.

Both the BASIC mode and SMART mode use the user program

start times, watering days, omit times/days, and several

Advanced Menu (rain delay, zone to zone delay, and master valve

settings).

Important Note: Zone run times must be entered for every zone

in use for the controller to recognize the zone in either BASIC or

SMART modes.

Содержание SmartWire 9600TW

















































Результаты поиска

Содержание SmartWire 9600TW

Отзывы:

Похожие инструкции для SmartWire 9600TW

Бренды по названию

Популярные бренды

Weathermatic SmartWire 9600TW, Руководство пользователя

Результаты поиска

Содержание SmartWire 9600TW

Отзывы:

Похожие инструкции для SmartWire 9600TW

Бренды по названию

Популярные бренды