WaveWare SPS v9S Скачать руководство пользователя страница 34

Страница: 34 / 57

Appendix B – Com Port Settings

You may be required to configure the

Com Port Settings

in the paging encoder to establish the appropriate operating

mode and serial communication parameters. Com Port Settings are Programmable using the

Encoder Setup Software.

This is done using the

WaveWare v

Series

Encoder Setup

Software that you can find on the WaveWare

Product

Support CD

(Shipped with each

Series Paging System) or from our

Website

at:

http://www.wirelessmessaging.com/SPS-5_Software.html

Your

WaveWare v

Series

Paging System

typically communicates with a PC or other host system via RS-232 at 9600

Baud, 8 data bits and 1 stop bit. You can configure the paging system for other serial communication parameters.

The available operating modes include

TAP Verbose, TAP Non-Verbose, COMP1, COMP2 Verbose, COMP2 Non-

Verbose, Scope

and

WaveWare Protocols.



TAP and COMP2 Verbose

means that the Paging System will include Human Readable Messages after

each Paging Request is received.



WaveWare and Scope

are

Proprietary

Single Serial Command Strings that includes Cap Code, Function

Code, RF Data Rate, and Message Values. Either protocol can be used as either

Simplex

Duplex

Operation



COMP2

means that the Data Formatted as

PagerID<CR>Message<CR>

GroupID<CR>Message<CR>

will cause the Message to be delivered to the Specified Pager ID or Group ID.



TAP Non-Verbose

reduces the Paging System Human Readable Response to 3-Digit Numeric Codes. In the

COMP2 Non-Verbose mode the response is reduced to none at all.



The Non-Verbose

modes are useful in situations where you want to minimize the Serial Data throughput

requirements which tend to allow Paging Messages to be delivered more quickly, or to achieve compatibility
with legacy host systems.



COMP1

means that any Data received on the Serial Port will be sent to all Pagers in Group 1 stored in the

Pager Database. Refer to

Appendix H

for a definition of the

COMP1

Protocol

Refer to

Appendix A

for a definition of the

TAP

Protocol

and

Appendix I

for a definition of the

OMP2

Verbose and Non-

Verbose Protocols

Independent of Operating Modes, you can configure the Serial Port

Baud and Parity

, and you can configure whether

Hardware or Software Flow Control

is used.

To get to the Com Port Settings in the

Paging Encoder v

Setup Software

, on the Main Screen click on

“Settings”.

See Pages:

20- 24 of this

Manual

for the

Series

Paging System

Model

you have.

This Completes the “Com Port Settings”.

Содержание SPS v9S


























































Результаты поиска

Содержание SPS v9S

Отзывы:

Похожие инструкции для SPS v9S

Бренды по названию

Популярные бренды

WaveWare SPS v9S, Руководство пользователя

Результаты поиска

Содержание SPS v9S

Отзывы:

Похожие инструкции для SPS v9S

Бренды по названию

Популярные бренды