background image

 

 

Quick Start Guide 

 

Your 

SPS- 5

 v

9

 Series Paging Systems should include: 

 

1- Rubber Duck Style Antenna, 1- Power Supply, 1- Serial Cable, 1- Package of Mounting Hardware and 1- 

Product Support CD.  A Second RS-232 Cable is available for Purchase if Required. 

Notes: 

 The 

Frequency, Cap Code(s)

Watts and other Information

 are

 

“Labeled”

 on the 

Back

 of the unit. 

 The 

SPS-5 

will 

“Auto Detect”

 the 

Encoder Setup Software

 for 

Pager Database Programming

 The attached 

Host System

 will usually need to send a 

3-Digit Pager ID

 to the 

SPS-5 

  

Paging System

 After 

Programming the Database

, attach the 

Serial Cable

 to the 

Host System

 that 

Initiates the Page

Installation: 

 The 

SPS-5 

has 

Mounting Holes

 on the 

Back

 

of the Unit

 for 

Wall Mounting

 

Remove

 the 

Front Cover

 to access these 

Mounting Holes 

and use the 

Screws and Anchors

 provided. 

 

Programming 

the

 SPS-5 

  

Paging System:  

Note: The 

Red

 LED will be Lit when you “Read/Edit/Program”.

 

 Attach the 

SPS-5 

  

Paging System

 to a Laptop or Desktop Computer running Windows XP Pro or Windows 7 Pro. 

 Install the

 “Encoder Setup v

9

” 

Program from the

 “Product Support CD”

. This Program does “

Both

”, 

v

9

 and 

v

9

S

Com Port: 

 Choose the 

Com Port (

Number

)

 you will use and then 

Click

 on the Com Port 

Button

 to Open the Port. 

 The 

RED

 

light 

next to the 

Com Port Button

 will then turn 

“GREEN”

 to show that the port is 

Open

 The 

Software

 will tell you that the 

“Encoder Database will now be Read” 

and you 

MUST

 click 

OK

 

Note:

 You 

MUST

 read the 

Database

 

BEFORE

 Adding or Changing the Database information. 

Pager Database: 

 Click on the 

Pager “Families” 

Icon 

(Far Left)

 to Add or Change the Quantity of Pager(s), Add or Change the Pager ID 

Number(s) and Add or Change the Cap Code(s) and Baud Rate(s). 

 The 

Function Code

 is

 “Normally”

 

set to 4 for 

Alphanumeric Pagers

 and set to 

1

 for 

Numeric Pagers

 After 

Entering

 all the 

Pager Information

 click the 

“OK”

 

Button

 at the bottom of the screen. 

 The Software will check for any 

Conflicts

 with the Information you have entered. If so, you will need to correct the 

problem(s) and Click

 

“OK”

 

again to verify all 

Conflicts

 were corrected. 

Settings: 

 Click on the

 “Settings” 

Icon 

(In the Middle)

 in order to setup the 

Communications

 

“Protocol”

 for the Com Port used 

with the 

Host System

 In the 

Encoder “Settings”

 

Screen

, choose the 

“Protocols” 

needed for 

Communications

 with the 

Host System

 

along with the other 

Com Port

 settings as needed. 

A

dvance Settings: 

 The

 “Advance Encoder Settings”

 were configured before shipment, but if you need to access those settings the 

password is

 maint

, (not case sensitive). 

 If you are not sure how to set the

 “Advanced Encoder Settings”

, you can click on the

 

“Restore Defaults”

 Button

 to 

set it to 

“Factory Settings” 

and click 

“OK”.

 

 

Click

 on the

 

“Program Encoder”

 

(Green Down Arrow) 

Button

 to 

Program

 the 

SPS-5 

Encoder.

 

Testing 

the

 

SPS-5   

with

 Pagers: 

 Click on the

 “Test Encoder Icon”

 on the 

Main Screen

 (Far Right)

 to send a 

“Test Page” 

to a pager. The Test 

Encoder function should “reboot” the encoder into the protocol, baud, and parity that the encoder was programmed 
to operate at. The status bar on the Test Encoder window should display the protocol, baud, and parity that the 
encoder is currently operating at. The Test Encoder window should adjust to the features that the selected protocol 
supports. 

 Enter the 

Pager ID

 Number in the

 “PIN” 

or

 “Cap Code” 

Field of the pager you want to test. (For TAP, PET, and 

COMP2 protocols, using the Pager Families section of the pager database, a 

3-Digit

 Number should be entered in 

the PIN field. For other protocols, you may want to enter a full 7 digit cap code value). 

 Enter a 

Message

 that you want to 

send

 to the pager. 

 The 

GREEN

 “RF TX LED” 

on the paging system should light up for a few seconds while the message is being sent to 

the pager. 

 You can observe the 

Com Port Log

 at the bottom of the screen to see the paging system status as each message is 

sent.                                    

The “Programming Guide” is Next…

 

Содержание SPS v9S


























































Отзывы: