background image

WL2 FW 

Manual

 

Page 5 – Revision EU05-07-17

 

 

 

 

 

  

WARNING! 

CONNECT TO POTABLE WATER SUPPLY. 

This system is to be used for water only and 

is not intended for use where water is microbiologically unsafe or with water of unknown quality 

without adequate disinfection. System is designed for the supplemental bactericidal treatment of 

public drinking water, or other drinking water, which has been tested and deemed acceptable for 

human consumption by the water provider. The system is designed to reduce normally occurring 

non-pathogenic or nuisance microorganisms only. System is not intended for treatment of 

contaminated water.

 

 

WARNING! 

TIP HAZARD. 

Dispenser could tip or fall causing serious injury. Always install unit on a 

firm, flat, and level surface and secure the 

WL2FW Water Treatment System 

to the base cabinet 

with the screw provided to lock the components together. Secure unit to cabinet, wall, or floor if 

needed. Never place heavy items on top of unit and never climb, stand, or hang on unit or storage 

cabinet to prevent injury and damage.

 

  

WARNING! 

UNIT IS HEAVY. TWO PERSON LIFT REQUIRED. 

Transport unit empty and always use 

material handling equipment or two people with proper lifting technique to reduce injury risk.

 

  

WARNING!  

STORE AND TRANSPORT UNIT EMPTY.   ALWAYS SANITIZE BEFORE USE.

 

The unit must be completely drained and sealed before storing to avoid stagnation and reduce 

microbiological contamination (potential bacterial growth). Sanitize before use to eliminate any 

potential microbiological contaminates

 

 

CAUTION! 

INDOOR USE ONLY. 

Intended for household use only. Never expose to direct sunlight, 

heat sources, or ambient air temperature above 37°C (100°F) or below 2°C (35°F). Install indoors 

and keep unit away from excessive humidity.  Never expose to freezing temperatures.  Ensure 

there is adequate clearance around the unit (50mm minimum) to allow refrigeration system 

condenser to dissipate heat.  Warmer environments require more clearance around the unit.

 

Installs where the ambient temperature exceeds 27°C (80°F), require a minimum of 100mm 

clearance for proper heat dissipation and efficient operation.

 

 

CAUTION! 

USE A WATER PRESSURE REGULATOR. 

Waterlogic will not be responsible for injury or 

damage caused by excessive water pressure. Input or feed pressure must be 2.7Bar to 4Bar (2.7 to 

4bar). Be aware of any potential pressure surges caused by building/municipal pumping stations. 

Water block devices and external leak detectors are strongly recommended. Locate the unit as 

close to the water supply and the electrical connections as possible to minimize risk.

 

 

CAUTION! 

USE PROPER SUPPLY LINES AND FEED WITH POTABLE AMBIENT WATER ONLY.

 

Feed water over 37°C (100°F) may damage the treatment components. Always use supply lines 

with adequate pressure rating and UV resistance. Close water supply valve and contact service 

representative if a leak is noticed.

 

Contact Waterlogic for assistance or help finding an Authorized Service Representative.

 

Содержание WL2FL Free Standing
















































































Отзывы: