WAGO 750-677 страница 88 Скачать руководство пользователя

Страница: 88 / 108

88 Diagnostics

WAGO I/O System 750 XTR

750-677/040-000 4PWM 24 VDC 0.2A XTR

Manual

Version 1.0.0

Diagnostics

9.1

Behavior of the I/O module in the event of an error

The I/O module always only allows the display of 1 error. If an error condition is

detected, the corresponding status bit is set. Bits used for application purposes

are hidden.

Some errors cause several error states to apply. For this reason, error states

have a prioritization. If several errors are present, the error with the higher priority

is always displayed.

Observe the display duration of diagnoses!

A diagnosed error condition is displayed for at least a duration of of 200 ms, even

if the detected error state is no longer present during this period. If a higher-

priority error state occurs during this period, the higher-priority error state is

immediately displayed for 200 ms and the lower-priority error state is lost.

The following prioritizations apply:

Table 61: Prioritization of Status Information

Status

Prioritätsstufe

Undervoltage

High

Short circuit

Medium

Output driver activated

Low

PWM active
PWM started
Output state

9.2

Diagnostics via Status Byte

Table 62: Status Byte 0

Bit

Explanation

Short circuit DO 1 or DO 2

Undervoltage

General error bit

Table 63: Status Byte 2

Bit

Explanation

Short circuit DO 3 or DO 4

Undervoltage

General error bit

Содержание 750-677













































































































Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды

WAGO 750-677, Руководство пользователя

Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды