WAGO 750-677 Скачать руководство пользователя страница 84

Страница: 84 / 108

84 Commissioning

WAGO I/O System 750 XTR

750-677/040-000 4PWM 24 VDC 0.2A XTR

Manual

Version 1.0.0

Example 3:

Channel 1/2:

Pulse Frq-Cnt

Channel 3: PWM DC

Channel 4: PWM Frq

Figure 31: Data Dialog, Example 3

A complex operating mode (Pulse Frq-Cnt) is preset for

Channel 1/2

The function results from the interaction of both channels and is therefore

combined. The process data value (frequency) can be entered as a value. The
counter (actual value) is displayed and can be reset with the adjacent button ( ).
The counting direction is set by pressing the arrow keys (

Channel pair 1/2 is not enabled (checkbox not selected), the associated output is

therefore high-impedance (Tri-state).

The selection for

Channel 3

and

Channel 4

in this example corresponds to the

selection for Channels 1 and 2 from Example 1. The release for channel pair 3/4

is not set, the associated output is therefore high-impedance (Tri-state).

Tip: If you click with the right mouse button in an input field for output data, the

context menu opens with further display options:

Figure 32: Context Menu

Among other things, you can switch between the number presentations.

Содержание 750-677













































































































Результаты поиска

Содержание 750-677

Отзывы:

Бренды по названию

Популярные бренды

WAGO 750-677, Руководство пользователя

Результаты поиска

Содержание 750-677

Отзывы:

Бренды по названию

Популярные бренды