WAGO 750-677 Скачать руководство пользователя

Страница: 101 / 108

WAGO I/O System 750 XTR

Service 101

750-677/040-000 4PWM 24 VDC 0.2A XTR

Manual

Version 1.0.0

Service

11.1 Factory Setting (Default Values)

The following values in the registers and parameters are factory settings:

Table 74: Factory Settings – Default Values

Parameter

Default-Wert

Watchdog timer

activated

Bridge mode

deactivated

Operating mode

PWM DC

Frequency

250 Hz

Duty cycle

50 %

Pulse width

50 µs

Reference potential

(load between output and... )

out

11.2 Firmware Update/Downgrade

You can update firmware on the Series 750 I/O Modules with the software

“WAGO I/O-Update 750.” The I/O modules can be updated via the service

interface or, for ETHERNET-based fieldbuses, via the fieldbus connection on the

fieldbus coupler/controller.

Observe the following information:

Do Not Switch Off the I/O Module!

Interrupting the update process can damage the I/O module.

Do not remove the I/O module during the update process. Do not interrupt the

power supply!

•

Ensure that communication with the fieldbus coupler/controller is not

interrupted during the update process.

•

Any PLC application running on the controller must be stopped before the

update process.

•

Before an update via the service interface, disconnect the fieldbus cable

from the fieldbus coupler/controller.

•

Do not close the software during the update.

•

Only run the software from a local hard disk.

Содержание 750-677













































































































Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды

WAGO 750-677, Руководство пользователя

Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды