WAGO 750-677 Скачать руководство пользователя

Страница: 47 / 108

WAGO I/O System 750 XTR

Operating Modes 47

750-677/040-000 4PWM 24 VDC 0.2A XTR

Manual

Version 1.0.0

4.2

PWM Frq

In this operating mode, the frequency can vary from 0… 20 kHz via the process

image. The duty cycle can be preset in the Parameterization dialog. The default

value is “50 %”.

All four available channels can be used independently of each other. To double

the output current, it is possible to connect a channel pair (DO 1 and DO 2 or DO

3 and DO 4) in parallel. “Bridge mode” must be enabled in the settings. The

operating mode and the values of the first channel (DO 1 or DO 3) are also

applied to the respective parallel channel (DO 2 or DO 4). The output data of the

parallel channel in the process image is irrelevant in bridge mode.

The corresponding channel pair is now synchronized. The load must be wired

accordingly at both outputs of the channel pair.

4.2.1

Process Image

Table 29: Process Image (PWM Frq)

Process Image

Input

Output

Status byte 0

Control byte 0

DO1 Frequency low byte

DO1 Frequency high byte

Status byte 1

Control byte 1

DO2 Frequency low byte

DO2 Frequency high byte

Status byte 2

Control byte 2

DO3 Frequency low byte

DO3 Frequency high byte

Status byte 3

Control byte 3

DO4 Frequency low byte

DO4 Frequency high byte

Table 30: Control Byte 0 (PWM Frq)

Control byte 0

Bit 7

Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0

RegCom

Enable DO 1 &

DO 2 Drivers

Legend

Enable DO 1 & DO 2

Drivers

0: The output driver for DO 1 & DO 2 is disabled.
1: The output driver for DO 1 & DO 2 is enabled.

RegCom

0: Register communication is switched off.
1: Register communication is switched on.

Содержание 750-677













































































































Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды

WAGO 750-677, Руководство пользователя

Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды