WAGO 750-677 Скачать руководство пользователя

Страница: 39 / 108

WAGO I/O System 750 XTR

Device Description 39

750-677/040-000 4PWM 24 VDC 0.2A XTR

Manual

Version 1.0.0

3.7.1

Notes and Limitations on Areas of Application

3.7.1.1 Power plants and voltage substations

When used in power plants and in high/medium voltage substations,

the

cables

to the actuators

must be shielded from a length of 10 m upwards.

For the complex operating modes (PWM Frq-Cnt, Pulse Frq-Cnt and PWM

Pulse-Dir), the cables to the actuators must be shielded from a length of 2 m.

For the complex operating modes

, an additional cable length restriction of the

field supply to 2 m applies for unshielded cables.

When using shielded cables, this additional restriction does not apply.

3.7.1.2 Residential Applications

When used in residential buildings according to EN 61000-6-3, a maximum

permissible cable length applies (cable capacitance wire to shield of max. 170

pF/m) depending on the frequency:

Figure 7: Diagram for Determining the Cable Length in Residential Applications

The cable length shown in the diagram applies per channel when all channels

are occupied.

The total length of the connected cables of all channels is critical. If fewer

channels are used or individual channels are provided with shorter cables, the

remaining cable lengths can be made longer.

Содержание 750-677













































































































Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды

WAGO 750-677, Руководство пользователя

Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды