WAGO 750-677 Скачать руководство пользователя

Страница: 15 / 108

WAGO I/O System 750 XTR

Important Notes 15

750-677/040-000 4PWM 24 VDC 0.2A XTR

Manual

Version 1.0.0

Do not exceed the maximum total current for I/O modules (5 VDC) via data

contacts!

The maximum permissible total current for internal system supply of the I/O

modules may not be exceeded. The permissible total current is specified in the

technical data of the head station and power supply. The data contacts for

internal system supply can be damaged and the permissible operating

temperature can be exceeded by higher values.

When configuring the system, do not exceed the permissible total current. If there

is a higher power requirement, you must use an additional supply to provide the

system voltage (5 VDC)!

Ensure proper contact with the DIN-rail!

Proper electrical contact between the DIN-rail and device is necessary to

maintain the EMC characteristics and function of the device.

Replace defective or damaged devices!

Replace defective or damaged device/module (e.g., in the event of deformed

contacts).

Protect the components against materials having seeping and insulating

properties!

The components are not resistant to materials having seeping and insulating

properties such as: aerosols, silicones and triglycerides (found in some hand

creams). If you cannot exclude that such materials will appear in the component

environment, then install the components in an enclosure being resistant to the

above-mentioned materials. Clean tools and materials are imperative for

handling devices/modules.

Clean only with permitted materials!

Clean housing and soiled contacts with propanol.

Do not use any contact spray!

Do not use any contact spray. The spray may impair contact area functionality in

connection with contamination.

Содержание 750-677













































































































Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды

WAGO 750-677, Руководство пользователя

Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды