WAGO 750-677 страница 100 Скачать руководство пользователя

Страница: 100 / 108

100 Use in Hazardous Environments

WAGO I/O System 750 XTR

750-677/040-000 4PWM 24 VDC 0.2A XTR

Manual

Version 1.0.0

10.2.2 Special Notes Regarding UL Hazardous Location

For UL Hazardous Location acc. to UL File E198726, the following additional

requirements apply:

•

Use in Class I, Division 2, Group A, B, C, D or non-hazardous areas only

•

ETHERNET connections are used exclusively for connecting to computer

networks (LANs) and may not be connected to telephone networks or

telecommunication cables

•

WARNING

– The radio receiver module 750-642 may only be used to

connect to external antenna 758-910!

•

WARNING

– Product components with fuses must not be fitted into circuits

subject to overloads!

These include, e.g., motor circuits.

•

WARNING

– When installing I/O module 750-538, “Control Drawing No.

750538” in the manual must be strictly observed!

Additional Information

Proof of certification is available on request.

Also take note of the information given on the operating and assembly

instructions.

The manual, containing these special conditions for safe use, must be readily

available to the user.

Содержание 750-677













































































































Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды

WAGO 750-677, Руководство пользователя

Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды