WAGO 750-677 Скачать руководство пользователя

Страница: 6 / 108

Notes about this Documentation

WAGO I/O System 750 XTR

750-677/040-000 4PWM 24 VDC 0.2A XTR

Manual

Version 1.0.0

Notes about this Documentation

Always retain this documentation!

This documentation is part of the product. Therefore, retain the documentation

during the entire service life of the product. Pass on the documentation to any

subsequent user. In addition, ensure that any supplement to this documentation

is included, if necessary.

1.1

Validity of this Documentation

This documentation is only applicable to the I/O module 750-677/040-000

(4PWM 24 VDC 0.2A XTR).

The I/O module 750-677/040-000 shall only be installed and operated according

to the instructions in this manual, in the system description for the WAGO I/O

System 750 XTR and in the manual for the used fieldbus coupler/controller.

Consider power layout of the WAGO I/O System 750 XTR!

In addition to these operating instructions, you will also need the system

description “Design Notes XTR – Guidelines and Recommendations for

Increasing Operational Safety” and the manual for the used fieldbus

coupler/controller, which can be downloaded at

www.wago.com

. There, you can

obtain important information including information on electrical isolation, system

power and supply specifications.

1.2

Copyright

This Manual, including all figures and illustrations, is copyright-protected. Any

further use of this Manual by third parties that violate pertinent copyright

provisions is prohibited. Reproduction, translation, electronic and phototechnical

filing/archiving (e.g., photocopying) as well as any amendments require the

written consent of WAGO GmbH & Co. KG, Minden, Germany. Non-observance

will involve the right to assert damage claims.

Содержание 750-677













































































































Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды

WAGO 750-677, Руководство пользователя

Результаты поиска

Содержание 750-677

Отзывы:

Похожие инструкции для 750-677

Бренды по названию

Популярные бренды