Volvo MD2010 Скачать руководство пользователя страница 61

Страница: 61 / 81

Checking of pressure valve in filler cap

Special tool:

999

6662

Drain off the refrigerant and connect the pressure

testing device with a nipple to one of the plugged

holes in the cooling system.

2. Extend the drain hose from the filler pipe with a

hose the end of which is placed in a vessel contain-

ing water.

3. Apply the pressure and read off the manometer

when the valve opens (water bubbles in vessel).

The valve should open at 0.9 kp/cm

(12.8 lbf/in

4. Remove the test equipment. Fit the plug and fill up

with refrigerant.

Drain off the water in the sea and fresh water sys-

tems.

Fig. 106. Heat exchanger insert

Fill up with refrigerant.

Cooling system

2. Release the hose clips and remove the rubber

muffs at the front and back of the heat exchanger.

Pull out the insert.

3. Flush and clean the insert inside and outside.

Clean also the housing.

Note:

If there are loose deposits in the insert a suit-

able steel rod can be pushed through the tubes in

the opposite direction to the flow of water.
NOTE! Make sure that the rod does not damage

the tubes.

4. Fit the insert in the heat exchanger.

NOTE! Make

sure that the insert is positioned correctly. Make

sure that the hole in the insert casing comes oppo-

site the hole in the housing and that the vent hole

comes upwards. The insert is marked with "UP".
Place the insert so that its extruding parts are equal

at the front and back.

Fit the rubber muffs on the heat exchanger's front

and back and tighten the hose clips. Connect the

hose from the sea water pump and tighten the clip.

Open the bottom cock or the cock on the S-drive

and start the engine. Check that no leakage occurs.

Cleaning of heat exchanger

Clean the heat exchanger insert on signs of blocking

(slow rise in refrigerant temperature).
NOTE! Check/clean the sea water filter first. Check also

the sea water pump's impeller and sea water intake.

Important!

Close the bottom valve before

working on the cooling system.

Содержание MD2010


















































































Результаты поиска

Содержание MD2010

Отзывы:

Похожие инструкции для MD2010

Бренды по названию

Популярные бренды

Volvo MD2010, Руководство по ремонту

Результаты поиска

Содержание MD2010

Отзывы:

Похожие инструкции для MD2010

Бренды по названию

Популярные бренды