Volvo MD2010 Скачать руководство пользователя страница 55

Страница: 55 / 81

Setting engine speed (RPM)

Check that the throttle mechanism functions normally.

Check that the throttle arm (1) (Fig. moves towards low

idle (2) when the throttle mechanism is in idling position

and moves towards the stop screw at wide open throttle

(WOT) (3) when the throttle mechanism is at wide open

throttle (WOT). Adjust the throttle mechanism if neces-

sary. Also check that the air filter and air intake are not

blocked.

IMPORTANT!

The engine speed (RPM) and

fuel quantity are factory set to give maximum

output and minimum environmental impact. The-

se settings must not be changed
Seals on the fuel injection pump may only be

broken by authorised personnel. Broken seals

must always be resealed

1. Check that gap (6) (Fig. 92) is approximately 3 mm

when the throttle mechanism is in the idling posi-

tion. If necessary: Slacken off the locknut (7) and

adjust until the correct gap is obtained with the

screw (8).

2. Warm up the engine and check the idling speed

using a workshop tachometer (see Technical Data

for correct idling speed).

3. If necessary, adjust to the correct idling speed

using the adjustment screw (2).

4. Check gap (3) again according to point 1.

Engine racing (high idling speed)

Warm up the engine and check the engine racing speed

using a workshop tachometer when the engine has no

load at wide open throttle (WOT) (see Technical Data

for correct engine racing speed).

Adjust if necessary as follows:

1. Slacken off the stop screw (3) so that it does not li-

mit the movement of the throttle arm (1).

2. Run the engine with no load at wide open throttle

(WOT) and adjust to the correct rev speed using

the adjustment screw (4) (remember to reseal the

screw).

3. Adjust the stop screw (3) so that there is a clearan-

ce of 0.1 mm between the stop screw (3) and the

throttle arm (1) when the throttle mechanism is at

wide open throttle (WOT).

Feed pump

Fuel

system

Fig. 92. Setting engine speed (RPM)

Dismantling of feed pump

1. Throttle arm

1. Wash clean round the pump.

2. Adjustment screw, low idling speed

3. Stop screw, wide open throttle (WOT)

Adjustment screw, engine racing

5. Adjustment screw, maximum quantity of fuel

2. Close the fuel cocks. Release the fuel connections

from the pump.

Dismantle the feed pump from the cylinder block.

Low idle speed

Empty the pump of fuel.

Содержание MD2010


















































































Результаты поиска

Содержание MD2010

Отзывы:

Volvo MD2010, Руководство по ремонту, Страница: 55 / 81

Результаты поиска

Содержание MD2010

Отзывы: