Volvo MD2010 Скачать руководство пользователя страница 38

Страница: 38 / 81

Engine body

Timing gears

Replacement of front crankshaft seal

The seal consists of a rubber ring and can be replaced

after the crankshaft pulley has been removed. Use a

universal extractor.
1. Tap in one side of the seal so that it goes on edge.

Pull out the seal with a hook.

Fig. 54. Fitting of crankshaft seal

3. Oil in the new seal with fit it with a suitable man-

drel.

Fig. 55. Fitting of crankshaft pulley

4. Remove the fitting tool. Fit the key and crankshaft

pulley.
See Technical data for tightening torque.

Dismantling of the timing gear

WARNING!

If the crankshaft and camshaft are

turned without being synchronised with each

other the valves can go against the pistons and

be damaged.

1. Close the fuel cocks. Remove both battery leads.

2. Close the bottom valve. Release the rubber hoses

to the sea water pump and drain out the water in

the sea water system.

3. Remove the sea water pump.

4. Remove the drive belt for the alternator.

Fig. 56. Dismantling of crankshaft pulley

5. Remove the pulley from the crankshaft. Use a uni-

versal extractor (Use an adjustable spanner on the

lug on the pulley as a counterhold when the nut is

removed)

6. Remove the delivery pipe complete. Release the

fuel house and fuel leak pipe at the injection pump.

Содержание MD2010


















































































Результаты поиска

Содержание MD2010

Отзывы:

Похожие инструкции для MD2010

Бренды по названию

Популярные бренды

Volvo MD2010, Руководство по ремонту

Результаты поиска

Содержание MD2010

Отзывы:

Похожие инструкции для MD2010

Бренды по названию

Популярные бренды