Volvo MD2010 Скачать руководство пользователя страница 33

Страница: 33 / 81

9. MD2O10, MD2020: Fit the circulation pump.

MD2030: Fit the circulation pump and thermostat

and spring (see Fig. 35).

10. Fit the glow plug, Tightening torque: see Technical

data. Fit the conductor rail and connect the electric

cable.

CIRD

MINK

11. Fit the copper gaskets, heat shields (MD2030) and

inserts (MD2O10-MD2030) to the injectors as per

Fig. 34.
Fit the injectors. Use socket L=80 mm (3.15 in),

key width = 22 mm (MD2O10-MD2030), and 27 mm

(MD2040).

Tightening torque MD2O10, MD2030, MD2040:

60-70 Nm (44.3-51.7 ft.lbs)
Tightening torque MD2030:

80-85 Nm (59.0-62.7 ft.lbs).

12. Put on new copper gasket and fit the fuel leak pipe.

Tighten the nuts and connect the return pipe.

13. Fit the delivery pipe complete. Tightening torque

20-25 Nm (14.8-18.4 ft.lbs).

14. MD2O10, MD2020, MD2030: Fit the induction mani-

fold.
MD2040: Fit the inlet pipe complete with air filter.

Fig. 35. Fitting of thermostat (MD2O10, MD2020,

MD2030) and expansion tank.

15. MD2O10, MD2020: Fit the rubber seal, thermostat

(3) and spring (2) in the heat exchanger housing (1)

Fig. 36. Fitting of thermostat (MD2040)

17. MD2040: Fit the rubber seal, thermostat and spacer

ring in the heat exchanger housing. Fit the cover

over the thermostat.

18. Connect the electric cables to the oil pressure re-

lay, and to the refrigerant temperature relay and

sensor (where appropriate).

Engine body

MD2010, -2020

MD2030

M D2040

16. Fit the expansion tank complete with heat exchan-

ger. Connect the hoses to the heat exchanger

housing and refrigerant pump. Tighten the hose

clips.

Fig. 34. Fitting of injectors

1. Injector

3. Heat shield (MD2030)

2. Copper gasket

4. Insert (MD2O10-2030)

Содержание MD2010


















































































Результаты поиска

Содержание MD2010

Отзывы:

Volvo MD2010, Руководство по ремонту, Страница: 33 / 81

Результаты поиска

Содержание MD2010

Отзывы: