Volvo MD2010 Скачать руководство пользователя страница 30

Страница: 30 / 81

Engine body

Checking of valve springs

Renovating the rocker mechanism

Check that the springs do not show any signs of

1. MD2O10, MD2020, MD2030: Remove the screws

damage.

at the front and rear of the rocker shaft.
MD2040: Screw in a M8 screw in the threaded hole

in the front edge of the rocker shaft. Fix the screw

head in a vice and pull out the rocker shaft (alt. a

withdrawing tool can be used).

Iry~

jrq p

-1

100

pso

Max. 2.0 mm (.0787 in)

Fig. 23. Checking of linearity

Place the valve springs on a level surface and check

the linearity with a st square (Fig. 23).

Fig. 24. Spring tester

Place the spring in a spring tester and check its length

both compressed and uncompressed.
The springs should maintain the values given in "Tech-

nical data".

Fig. 25. Dismantling of rocker mechanism (MD2040)

2. Dismantle the rocker mechanism. Remove the

rockers, springs and washers.

3. Clean the parts. Observe special care with the

rocker shaft's oil channels and oil holes in the rock-

ers.

Fig. 26. Measuring of rocker shaft

4. Check the wear on the rocker shaft with a microme-

ter (Fig. 26). Diameter min. 11.57 mm (.4555 in).

Содержание MD2010


















































































Результаты поиска

Содержание MD2010

Отзывы:

Похожие инструкции для MD2010

Бренды по названию

Популярные бренды

Volvo MD2010, Руководство по ремонту

Результаты поиска

Содержание MD2010

Отзывы:

Похожие инструкции для MD2010

Бренды по названию

Популярные бренды