Volvo MD2010 Скачать руководство пользователя страница 47

Страница: 47 / 81

025

038

031

076

Fig. 78. Check measuring of measuring plastic

3. Remove the cap and measure the width on the

pressed out measuring plastic at the widest point.

Use the scale which accompanies the measuring

plastic (Fig. 78).

Max. permissible big-end bearing clearance:

0.2 mm (.0078 in).

Replace the big-end bearing if the bearing clear-

ance exceeds the permissible value. If necessary

the journals can be ground to an undersize and

oversize bearings fitted. Big-end bearings are avail-

able in two oversizes.

NOTE!

Check the bearing clearance again before

assembly if the journals have been ground.

Fitting of the crankshaft

1. Check the cleaning of the crankshaft channels and

bearing surfaces, cylinder block and cap. Check

also that the bearing cups and their mating surfac-

es have no burrs or upset ends.

2. Place the main bearing in position in the cap.

Check that the lubrication holes in the top bear-

ing cups come opposite the oil channels.

3. Oil in the bearing and main bearing journals and fit

the caps on the crankshaft.

Note :

The bevelled edge (1, Fig. 79a and 79b)

should be turned forwards on all caps.

4. Fit the cap which is provided with a groove as per

2, Fig. 79a and 79b.

Note:

The bearing cups provided with an oil groove

(3, Fig. 79a and 79b) should be placed in the

top

cap.

MD2O10, MD2020, MD2030: Fit

aluminium

caps

(with integrated thrust washers) at the

far end

(fly-

wheel side).

MD2040: Place both thrust washers in the lower

cap at the far end (flywheel side) and with the oil

groove turned towards the crankshaft.

Fig. 79a. Fitting of main bearing cap MD2O10,

MD2020, MD2030

1. Big-end bearing cap with 4. Main bearing cap of

bevelling

cast iron

2. Groove

5. Main bearing cap of

3. Top main bearing half

aluminium

with oil groove

Engine body

Fig. 79b. Fitting of main bearing cap MD2040

1. Big-end bearing cap with 3. Top main bearing half

bevelling

with oil groove

2. Groove

4. Thrust washers

Carefully lift the crankshaft in position in the cylin-

der block.

Note:

Tape the crankshaft gear before the crank-

shaft is lifted in. The cogs can otherwise damage

the bearing surfaces in the cylinder block.

Содержание MD2010


















































































Результаты поиска

Содержание MD2010

Отзывы:

Volvo MD2010, Руководство по ремонту, Страница: 47 / 81

Результаты поиска

Содержание MD2010

Отзывы: