Volvo MD2010 Скачать руководство пользователя страница 48

Страница: 48 / 81

Engine body

6. Tighten the main bearing cap. Tightening torque,

see Technical data.

Fig. 80. Checking of axial clearance

7. Check that the axial clearance does not exceed

0.5 mm (.0196 in).

Replacement of gear ring on the flywheel

1. Mark up the position of the flywheel in relation to

the crankshaft (to simplify fitting). Dismantle the fly-

wheel.

2. Drill one or a couple of holes in a tooth gap on the

gear ring. Split the ring at the drilled hole with a

chisel, after which the gear ring can be removed.

3. Brush clean the mating surface on the flywheel with

a steel brush.

4. Heat up the new gear ring in an oven (120-150°C/

248-302°F) so that the gear ring becomes evenly

hot all round.

5. Place the heated gear ring on the flywheel and

drive on with a hammer and soft mandrel. The gear

ring should then cool in the free air.

6. Clean the mating surfaces on the flywheel and

crankshaft. Check the rear crankshaft seal. Re-

place if necessary.

7. Fit the flywheel in the correct position (guide pin on

MD2030 and MD2040).
Tightening torque, see Technical data.

Replacement of rear crankshaft seal

The seal consists of a rubber ring and becomes access-

ible after the adapter plate at the back of the flywheel

housing, the flexible coupling, flywheel* and flywheel

housing have been removed.

*Note:

Mark up the position of the flywheel in relation to

the crankshaft (simplified fitting).

1. Clean the position for the sealing ring in the cylinder

block and the mating surface on the flywheel hous-

ing.

Fig. 81. Fitting of crankshaft seal

2. Apply an even layer of sealing compound (VP no.

840 879) round the flywheel housing's mating sur-

face (screw holes).

Apply grease on the sealing lip and fit the seal.

3. Fit the flywheel housing, flywheel, the flexible coup-

ling, and the adapter plate.
Tightening torque, see Technical data.

Содержание MD2010


















































































Результаты поиска

Содержание MD2010

Отзывы:

Похожие инструкции для MD2010

Бренды по названию

Популярные бренды

Volvo MD2010, Руководство по ремонту

Результаты поиска

Содержание MD2010

Отзывы:

Похожие инструкции для MD2010

Бренды по названию

Популярные бренды