manualshive.com logo in svg

Volvo MD2010, Руководство по ремонту, Страница: 64 / 81

Поделиться
Скачать
Volvo MD2010 Скачать руководство пользователя страница 64

General

The engines are fitted with AC generators. The system
voltage is 12V.

MD2010A, -2020A, -2030A and -2040A are fitted with a
1,5-pole* electrical system, while MD201OB/C, 2020B/

C, 2030B/C and 2040B/C have a one-pole system.

Note: One-pole during the start procedure via an

earthing relay.

68

Electrical system

The electrical system also includes as accessories re-

l ays for the monitoring of the engine's refrigerant tem-
perature and oil pressure.

The electrical system is illustrated in two ways. The wir-

i ng diagram (page 80) shows the wiring, cable areas
and colours.

Where respective parts are positioned on the engine is
shown in the figures below.

Positioning of electrical components on the engine

Fig. 111. Positioning of electrical components on the engine

10

1. Starter motor

8. Fuses (4 pcs),

2. Earthing relay (A-version)

max. 15A (-) (A-version)

3. Glow plug

9. Oil pressure relay,

4. Alternator

(accessory)

5. Starter relay

10. Oil pressure sensor

6. Glow relay

11. Refrigerant temperature relay

7. Fuses (4 pcs),

(accessory)

max. 15A (+)

12. Refrigerant temperature sensor

Содержание MD2010


















































































Отзывы:

Нет отзывов