Volvo MD2010 Скачать руководство пользователя страница 27

Страница: 27 / 81

Stripping of cylinder head

Fig. 14. Dismantling the valves

1. Valve lock

4. Valve

2. Valve spring washer 5. Valve cap*

3. Valve spring

and later versions

, 2020, 2030

1. Remove the valves and valve springs. Press the

springs together with a valve spring tensioner and

remove the valve lock. Place the valves in order in

a marked valve rack. Remove the valve stem seals.

2. Clean all parts. Observe special care with the

channels for oil and refrigerant.

3. Remove residual soot and impurities from the cylin-

der head's sealing surfaces.

Note:

Do not use use steel brush to clean the cylin-

der head screw threads or under the screw heads.

Engine body

I nspection of cylinder head

The flatness tolerance for the cylinder head is max. 0.12

mm (.00472"). Check in six positions ("A-F" as per Fig.

15 and 16). Use a feeler gauge and a ruler the sides of

which are precision rubbed as per DIN 874/Normal.

Fig. 15. Checking of cylinder head flatness

Fig. 16. Checking of cylinder head flatness

If the flatness is not within the permissible tolerance the

cylinder head should be replaced. If leakage or blow

marks are confirmed it is not necessary to check for flat-

ness since the cylinder head must be replaced.
Check the valve seats and that the pin screws are tight.
For replacement of the valve seats (inlet) see next

page.

Содержание MD2010


















































































Результаты поиска

Содержание MD2010

Отзывы:

Похожие инструкции для MD2010

Бренды по названию

Популярные бренды

Volvo MD2010, Руководство по ремонту

Результаты поиска

Содержание MD2010

Отзывы:

Похожие инструкции для MD2010

Бренды по названию

Популярные бренды