ViM TEDH F400, Техническое руководство, Страница: 23 / 60

23/60 NT00000658-TEDH-V-F400-ECOWATT-AN-210609
Register Address Function Range Active state
0x0014 13 Allow using Brake Chopper 0 - 1 1 = Allow BC
0x0014 14 Allow using Cooling Fan 0 - 1 1 = Allow Fan
0x0016 15
3 x 230V config
0 - 1
0 = Voltage values from CCF
1 = Fixed values for 3 x 230V
0x0017 16 1V start voltage 0 - 1
0 = Start @ 2V
1 = Start @ 1V
0x0018 17 Very High Switch Frequency 0 - 1
0 = 8 kHz as “HI SF”
1 = 10 kHz as “HI SF”
0x0019 18
Write protect config
0 - 1
0 = Allow change via Modbus
1 = “Lock” configuration
0x0020 19 Clear PowerLog (Wh, kWh, MWh) 0 - 1 1 = Clear Power Log
0x0021 20
Motor output off
0 - 1
1 = Keep motor output off
0x0022 21 Show alarm-type with LED-blink 0 - 1 1 = Use blink to show alarm
0x0023 22 Autodetect Control mode 0 - 1
1 = Analog control with temporary
Modbus override
0x0024 23 Set Output Pin (If Output Cfg=5) 0 - 1 0 = Output “Low”, 1 = “High”
0x0031 30 Analog Firemode 0 - 1 1 = active
5.3.2 Input Stat Bits
Available Input Stat Bits are shown in table below.
Input Stat Bits: 29 (R)
0x02: Read
Register Address Function Range Active state
1x0001 0 V LO Alarm 0 - 1 1 = Alarm
1x0002 1 V HI Alarm 0 - 1 1 = Alarm
1x0003 2 I HI Alarm (Motor out short) 0 - 1 1 = Alarm
1x0004 3 Temperature High 0 - 1 1 = Warning
1x0005 4 Input Phase Error 0 - 1 1 = Warning
1x0006 5 Rotor Blocked 0 - 1 1 = Alarm
1x0007 6 Current Limit 0 - 1 1 = Warning
1x0008 7 Voltage Limit 0 - 1 1 = Warning
1x0009 8 Rotor Direction 0 - 1 1 = Alarm
1x00010 9 EEPROM Error 0 - 1 1 = Warning
1x00011 10 Internal Stop 0 - 1 1 = Alarm (Stop)
1x00012 11 Earth fault (H5 only) 0 - 1 1 =Alarm
1x00013 12 Brake Chopper Fault 0 - 1 1 = Warning
1x00014 13 Motor Phase Error 0 - 1 1 = Alarm
1x00015 14 Communication error MOC 0 - 1 1 = Alarm
1x00016 15 V Ripple 0 - 1 1 = Warning
1x00017 16 Digital Input 1 0 - 1 1 = HI
1x00018 17 Digital Input 2 0 - 1 1 = HI
1x00019 18 Ext. 24V supply overload 0 - 1 1 = Overload
1x00020 19 MOC in bootloader 0 - 1 1 = Alarm
1x00021 20 Digital Input 3 (IOM) 0 - 1 1 = HI*
1x00022 21 Digital Input 4 (IOM) 0 - 1 1 = HI*
1x00023 22 Communication error IOM 0 - 1 1 = Warning*
1x00024 23 Motor Overheat (IOM) 0 - 1 1 = Alarm
1x00025 24 Windmilling 0 - 1 1 = Warning
1x00026 25 Rotation OK 0 - 1 1 = OK
1x00027 26
IO Config mismatch
0 - 1 1 = Warning
1x00028 27
Config write attempt
0 - 1 1 = Detected
1x00029 28 Unsaved UserData 0 - 1 1 = Unsaved
* Only if one of the IOM output functions is enabled.