Viking VFR400 Скачать руководство пользователя страница 10

Страница: 10 / 99

VFR-400 • 5403548 • REV W • 8/17

• Reverse polarity upon activation

• Power limited, Current limited

• Outputs identified as Release are Special Application. All other outputs are Regulated 24 VDC, rated 1 Amp each, 2.5 Amp

total for all circuits.

• End-of-Line-Resistor - 5.1k ohms

• Frequency - continuous

• Maximum voltage - 27 VDC

• Ripple voltage - .3 VDC

• Maximum impedance: 3 divided by NAC current draw

• Maximum resistance for outputs programmed as RELEASING:

1 divided by the current draw of the solenoid when activated

• Normal standy supervisory current - approximately .38mA

• Low current trouble activation - .11mA

• High current trouble activation - .63ma

Release Abort Circuit

• Available chemical mode only

• 1 momentary non-latching Class B circuit

• Power limited, current limited

• Maximum loop resistance - 100 ohms

• End-of-Line-resistance - 5.1k ohms

• Frequency - continuous

• Normal supervisory current - approximately 4mA

• Low current trouble activation - approximately 3.3mA

• Abort current condition - approximately 10mA

• Maximum voltage - 23VDC

NOTE: Mode 3 is not UL Listed

Mode 1 – (ULI) Activation of the abort circuit stops the pre-discharge timer at 10 seconds. If there is less than 10 seconds

remaining, the time goes back to 10 seconds. Releasing the abort switch starts the timer at 10 seconds.

Mode 2 – (IRI) Operates the same as the ULI mode except the abort circuit only functions if the abort button is pressed before the

second alarm is received by the panel. The panel must be programmed for cross zoning for the IRI mode to function.

Mode 3 – (NYC) This mode is not UL listed. Activation of the abort circuit during the pre-discharge countdown adds 90 seconds

to the original pre-discharge time. This is a one-time feature. Repeated pressing of the abort button has no effect. The

pre-discharge timer resumes when the abort button is released

Mode 4 – (30-Second Abort) This mode is not UL listed. Activation of the abort circuit stops the pre-discharge timer at 30

seconds. If there is elss than 30 seconds remaining, the timer goes back to 30 seconds. Releasing the abort switch starts

the timer at 30 seconds.

Low/Missing Battery

Causes battery and system trouble if battery falls below 22 volts. Battery circuit is fused and reverse polarity protection is provided.

Input Power

• Universal Input 120VAC, (60 Hz, 165VA) or 220VAC, (50 Hz, 185VA) 15 Amp Branch Line overcurrent protection required

• Power On indicator on LED annunciator module is extinguished on AC power loss (supervised)

• System trouble is also generated if voltage drops below 102V

Backup Power Requirements

• VFR-400 - Standby 121 mA, alarm 274 mA at 24VDC

Zones programmed as Manual Release cannot be aborted. If it is necessary to abort a manual station zone, program that zone as

Detection. Zones programmed as DETECTION containing manual release stations shall not be a part of a cross zone function

and shall have a maximum 30 second pre-discharge time delay.

If the pre-discharge timer is set at 0 the abort circuit will not stop the release circuit.

NFPA 12 prohibits the use of abort circuits on Suppression Systems employing carbon dioxide.

CAUTION

Содержание VFR400




































































































Результаты поиска

Содержание VFR400

Отзывы:

Бренды по названию

Популярные бренды

Viking VFR400, Руководство пользователя

Результаты поиска

Содержание VFR400

Отзывы:

Бренды по названию

Популярные бренды