Viking DDBF036LSS Скачать руководство пользователя | Manualshive

Страница: 46 / 50

background image

Disassembly Procedure

WARNING

To avoid risk of electrical shock, personal injury, or death, disconnect power to unit before servicing,

unless testing requires power.

46

©2007 Viking Preferred Service

Evaporator Fan Motor Assembly

Condition Requirements:
Access to Evaporator Section

1. Remove two screws from fan motor mount.
2. Disconnect evaporator fan wiring and ground from

motor.

3. Reverse procedure for installation.

Evaporator Fan Motor and Fan Blade

Condition Requirements:
Evaporator Fan Motor Assembly Removed

1. Remove evaporator fan blade by pulling blade off

evaporator fan shaft.

2. Remove fan motor by squeezing motor retainer clips

together to release retainer.

3. Remove retainer and slide motor out.

Evaporator
Fan Motor

Evaporator
Fan Clip

Shroud
Assembly

Fan Blade

4. Reverse procedure for installation.

Defrost Thermostat Removal

Condition Requirements:
Access to Evaporator Section

1. Cut wires to defrost thermostat and unclip

thermostat from evaporator coil.

2. Replace thermostat and use wire nut(s) included in

defrost thermostat kit.

3. Reverse procedure for installation.

Defrost Heater Removal

Condition Requirements:
Access to Evaporator Section

1.  Disconnect defrost heater connectors from harness.
2.  Remove two screws from evaporator coil.
3.  Grip evaporator tubing at left and right sides and tug

evaporator sharply forward. Evaporator will pop out
of plastic clips that hold it to back wall of unit. Then
roll bottom of evaporator forward and up, exposing
evaporator heater in its location amid fins at bottom
of evaporator.

4. Release heater clips and remove heater from

evaporator coil.

5. Reverse procedure for installation.

«
...
44
45
46
47
48
...
»

Содержание DDBF036LSS



















































Отзывы:

Нет отзывов

Похожие инструкции для DDBF036LSS

Бренд: DAEWOO ELECTRONICS Страницы: 15

Бренд: Galanz Страницы: 16

Бренд: Saba Страницы: 48

Бренд: U-Line Страницы: 24

Бренд: Amana Страницы: 17

Бренд: mabe Страницы: 37

Бренд: Midea Страницы: 12

Бренд: BOMANN Страницы: 24

Profile GTR12HBX

Бренд: GE Страницы: 56

Бренд: GE Страницы: 2

Бренд: Haier Страницы: 24

Бренд: Haier Страницы: 29

Бренд: Haier Страницы: 10

Бренд: Haier Страницы: 29

Бренд: Haier Страницы: 32

Profile PSW26PSWSS

Бренд: GE Страницы: 3

PSHS6YGXSS - Profile 26' Dispenser...

Бренд: GE Страницы: 2

Profile PFSS5NFXSS

Бренд: GE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды