Viking DDBF036LSS Скачать руководство пользователя страница 12

Страница: 12 / 50

Troubleshooting Chart

Symptom

Possible Cause

Corrective Action

Humidity levels are high or
door has been opened
frequently.

Reduce time door is open. Organize food items
efficiently to assure door is open for as short a time as
possible.

Water droplets form on
inside of refrigerator

Door gaskets are not sealing
properly.

Clean door gasket.

Refrigerator or ice
maker makes
unfamiliar sounds or
seems too loud

Normal operation.

See Operating Sounds.

Contents could be obstructing
drawer.

Reposition food items and containers to avoid
interference with the drawers.

Drawer is not in proper
position.

Verify drawer positioning.

Refrigerator is not level.

See Leveling.

Clean drawer channels with warm, soapy water. Rinse
and dry thoroughly.

Temperature-controlled
drawer and/or crisper
drawer do not close
freely

Drawer channels are dirty.

Apply a thin layer of petroleum jelly to drawer
channels.

Reduce time door is open.

Doors have been opened
frequently or for long periods
time.

Allow interior environment to adjust for period the door
has been opened.

Humidity or temperature in
surrounding area is high.

Normal operation.

Food has recently been
added.

Allow time for recently added food to reach
refrigerator or freezer temperature.

Refrigerator is exposed to
heat by environment or by
appliances nearby.

Evaluate your refrigerator’s environment. Refrigerator
may need to be moved to run more efficiently.

Condenser coils are dirty.

Clean coils.

Controls need to be adjusted.

Adjust controls.

Refrigerator is not level. Level refrigerator.

Door is not closing properly.

Check for internal obstructions that are keeping door
from closing properly.

Refrigerator runs too
frequently

Door gaskets not sealing
properly.

Clean door gaskets.

Ice maker has just been
installed or a large amount of
ice has been used.

Wait 24 hours for ice production to begin or for ice
maker to restock after emptied.

Water pressure is too low.

Check water pressure requirements.

Ice maker is not
producing enough ice
or ice is malformed

Water filter is clogged or
needs to be changed.

Change water filter.

Содержание DDBF036LSS



















































Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды

Viking DDBF036LSS, Руководство по обслуживанию

Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды