Viking DDBF036LSS Скачать руководство пользователя страница 48

Страница: 48 / 50

Disassembly Procedure

WARNING

To avoid risk of electrical shock, personal injury, or death, disconnect power to unit before servicing,

unless testing requires power.

Condenser Fan Motor and Blade Removal

Condition Requirements:
Access to Machine Compartment

1. Disconnect connector from condenser motor.
2. Remove two screws from mounting brackets

attached to motor.

3. Remove motor and fan blade out the rear of shroud.
4. Remove the retainer nut to remove fan blade.

5. Reverse procedure to reassemble.

Overload/Relay Removal

Condition Requirements:
Access to Machine Compartment

1. Discharge capacitor through a 10.000-ohm resistor.
2. Using fingers and standard screwdriver, press and

pry bale strap off the overload/relay/capacitor
assembly.

3. Reverse procedure for installation.

Compressor Removal

Condition Requirements:
Access to Machine Compartment

1. Remove bale strap which retains

overload/relay/capacitor.

2. Pull overload/relay/capacitor assembly off of

compressor terminals.

3. Disconnect ground wires attached to compressor.
4. Follow reclaiming procedures in Service Procedures

section of this manual.

5. Remove

drier.

6.  Unbraze low and high pressure lines at compressor.
7.  Remove three bolts and compressor from the unit.
8.  Reverse procedure for installation.

NOTE:

Install new drier and compressor per instructions

in “Service Procedures.” Evacuate and recharge
sealed system per instructions in Service
Procedures.

Condensate Drip Pan Removal

Condition Requirements:
Compressor Removed
Condenser Fan Motor Removed
Water Valve Assembly Removed

NOTE:

Condensate drip pan may have water in it. Wipe

up all water prior to removal.

1. Bend copper tubing up out of condensate pan to

allow removal of condensate pan.

2. Reverse procedure for installation.

Содержание DDBF036LSS



















































Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды

Viking DDBF036LSS, Руководство по обслуживанию

Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды