Viking DDBF036LSS Скачать руководство пользователя страница 43

Страница: 43 / 50

Disassembly Procedure

WARNING

To avoid risk of electrical shock, personal injury, or death, disconnect power to unit before servicing,

unless testing requires power.

Access to Machine Compartment

Condition Requirements:
None

1. Remove seven screws and cover from the unit.
2. Remove power cord from cover.

3. Reverse procedure for installation.

Water Filter Assembly Removal

Condition Requirements:
Water Filter Removed
Access to Machine Compartment

1. Remove filter cover by pulling rear left side of cover

to the left to release cover from holding pin.

2. Filter head can be released from holding bracket by

opening tabs on left side filter head and pulling
downward and to your left to release filter head.

3. Tubing needs to be disconnected from water valve

in the machine compartment. (See Water Valve
removal)

4. After tubing is loose from water valve pull the filter

head and tubing out the front of unit.

NOTE:

Make sure to note tubing end colors when

reinstalling new head and tubing assembly.

5. Reverse procedure for installation.

Water Tank Assembly Removal

Condition Requirements:
Drawers and Shelves Removed
Access to Machine Compartment

1. Remove two screws holding water tank to rear

bulkhead.

2. Disconnect tube from connector.
3. Tubing needs to be disconnected from water valve

in the machine compartment (See water valve
removal).

4. From inside of fresh food compartment pull tubing

up and out of cabinet to complete removal of water
tank.

5. Reverse procedure for installation.

Содержание DDBF036LSS



















































Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды

Viking DDBF036LSS, Руководство по обслуживанию

Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды