Viking DDBF036LSS Скачать руководство пользователя страница 24

Страница: 24 / 50

Component Testing

Component Description

Test

Procedures

ECM
condenser
motor

Condenser fan moves cooling air across
condenser coil and compressor body.

Condenser fan motor is in parallel circuit
with compressor.

Check resistance across motor. If no resistance
across motor, replace motor.

Evaporator fan
motor

Evaporator fan moves air across
evaporator coil and throughout
refrigerator cabinet.

1. Disconnect power to unit.
2. Disconnect fan motor leads.

3. Check resistance from ground connection

solder. Trace to motor frame must not exceed
.05 ohms.

4. Check for voltage at connector to motor with

unit in refrigeration mode and compressor
operating.

Refrigerator
light switch

Single pole, single throw switch
completes circuit for light when door is
open.

Check resistant across terminals.

Switch arm depressed

“NO”

terminals

Open

Switch arm up

“NO”

terminals

Closed

Freezer light/
Interlock
switch

Single pole, Double throw switch
completes circuit for light when door is
open. Completes circuit for dispenser
when door is closed.

Check resistant across terminals.

Switch arm depressed:

•

“NO” terminals Open

•

”NC” terminals Closed

Switch arm not depressed:

•

“NC” terminals Open

•

“NO” terminals Closed

Water valve

Controls water flow to the ice maker.

Controlled by thermostat in ice maker.

See Ice Maker section for further
information.

Check resistance across coil windings.

Drier

Drier is placed at post condenser loop
outlet and passes liquefied refrigerant to
capillary.

Desiccant (20) 8 x 12 4AXH - 7 M>S> -
Grams

Drier must be changed every time the system is
opened for testing or compressor replacement.

NOTE

: Drier used in R12 sealed system is not

interchangeable with drier used in R134a
sealed system. Always replace drier in
R134a system with correct part number.

Before opening refrigeration system, recover
HFC134a refrigerant for safe disposal.

1. Cut drier out of system using the following

procedure. Do not unbraze drier.

2. Applying heat to remove drier will drive

moisture into the system.

3. Score capillary tube close to drier and break.
4. Reform inlet tube to drier allowing enough

space for large tube cutter.

5. Cut circumference of drier 1 ¼" below

condenser inlet tube joint to drier.

6. Remove drier.

Содержание DDBF036LSS



















































Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды

Viking DDBF036LSS, Руководство по обслуживанию

Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды