Viking DDBF036LSS Скачать руководство пользователя страница 13

Страница: 13 / 50

Troubleshooting Chart

Symptom

Possible Cause

Corrective Action

Ice maker arm is up.

Confirm ice maker arm is down.

Household water supply is
not reaching water valve.

See Connecting the Water Supply.

Copper tubing has kinks.

Turn off water supply and remove kinks. If kinks
cannot be removed, replace tubing.

Water pressure is too low.

Check water pressure requirements.

Check freezer temperature.

Adjust temperature.

Ice bin is not installed
properly.

Check position of ice bin.

Ice maker is not
producing ice

Improper water valve was
installed.

See Connecting the Water Supply.

Water filter needs to be
replaced.

Change water filter.

Water filter indicator
light is red

Filter indicator sensor needs
to be reset.

See Filter Status Indicator Light.

Symptom

Possible Cause

Corrective Action

Water pressure is low.

Check water pressure requirements.

Saddle valve not open
completely.

Open saddle valve completely.

Improper water valve was
installed.

See Connecting the Water Supply.

Copper tubing has kinks.

Turn off water supply and remove kinks. If kinks
cannot be removed, replace tubing.

Water filter is clogged or
needs to be changed.

Change water filter.

Water flow is slower
than normal

Water valve not opened
completely.

Open water valve completely and check for leaks. The
minimum flow at dispenser is approximately 10 fluid
ounces in nine seconds with a new filter in place or
approximately 10 fluid ounces in five seconds without
a filter.

Water appears cloudy

Air or air bubbles in water.

This is normal when first using the dispenser and will
disappear with use.

Water pressure is low.

Check water pressure requirements.

Saddle valve not open
completely.

Open saddle valve completely.

Ice forms in inlet tube
to ice maker

Freezer temperature is too
high.

Adjust temperature.

Plastic tubing was used to
complete water connection.

The manufacturer recommends using copper tubing
for installation.

Refrigerator is leaking
water

Improper water valve was
installed.

See Connecting the Water Supply.

Содержание DDBF036LSS



















































Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды

Viking DDBF036LSS, Руководство по обслуживанию

Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды