Viking DDBF036LSS Скачать руководство пользователя страница 44

Страница: 44 / 50

Disassembly Procedure

WARNING

To avoid risk of electrical shock, personal injury, or death, disconnect power to unit before servicing,

unless testing requires power.

Water Dispenser Switch Removal

Condition Requirements:
Door Opened

1. Insert small screwdriver as shown to remove

dispenser cover plate.

2. Remove screw and pull dispenser out of unit.

3. Disconnect wires from switch and remove switch

from dispenser unit.

4. Reverse procedure for installation.

Freezer Section Light Bulb Removal

Condition Requirements

CAUTION

To avoid risk of burners, wear gloves when

replacing light bulb.

Freezer Drawer Opened

1. Remove light shield by pressing the upper right side

of the shield and rotating downward.

2. Remove light bulb.
3. Replace with appliance bulb no greater than 40

watts.

Freezer Section Light Socket Removal

Condition Requirements:
Freezer Light Bulb Removed
Freezer Drawer Removed

1. Remove screw to lower light socket housing from

unit.

2. Disconnect wires from light socket.
3. Squeeze retaining tab to release socket.

4. Reverse procedure for installation.

Содержание DDBF036LSS



















































Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды

Viking DDBF036LSS, Руководство по обслуживанию

Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды