Viking DDBF036LSS Скачать руководство пользователя страница 41

Страница: 41 / 50

Disassembly Procedure

WARNING

To avoid risk of electrical shock, personal injury, or death, disconnect power to unit before servicing,

unless testing requires power.

Refrigerator Section Light Bulb Removal

CAUTION

To avoid risk of burners, wear gloves when

replacing light bulb.

Condition Requirements:
Door Opened

1. Slide bulb cover to rear to release it from holding

tabs.

2. Remove light bulb.
3. Replace bulb with appliance bulb no greater than 40

watts.

Refrigerator Section Light Bulb Socket
Removal

Condition Requirements:
Light Bulbs Removed

1.  Remove socket plate from tabs.
2.  Disconnect wires from socket.
3.  Remove socket from socket plate.

4. Reverse procedure for installation.

Electronic Control Board Removal

Condition Requirements:
Light Bulbs Removed

1. Using a screwdriver, depress two tabs and lower the

control panel housing.

2. Disconnect connector from control board.
3. Unclip thermistor from control panel housing.

4. Disconnect ribbon connector and remove board

from tabs.

5. Reverse procedure for installation.

Light Switch Removal

Condition Requirements:
Door Opened

1. Use a taped putty knife to carefully pry light switch

out of liner.

2. Disconnect two wires from the light switch and

remove light switch from unit.

3. Reverse procedure for installation.

Содержание DDBF036LSS



















































Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды

Viking DDBF036LSS, Руководство по обслуживанию

Результаты поиска

Содержание DDBF036LSS

Отзывы:

Похожие инструкции для DDBF036LSS

Бренды по названию

Популярные бренды