Vector Welding C-Series, Руководство по эксплуатации

Страница: 66 / 81

123 122
MIG SERIES EQUIPMENT
Operation Operation
MIG SERIES EQUIPMENT
5. Digital Voltmeter
The digital meter is used to display the pre-set (preview) Voltage in Mig modes and
actual welding Voltage of the power source when welding. This digital meter is used to
display the Welding Output Terminal Voltage in STICK modes during non- welding or
welding.
7. Positive Control
The positive control is used to plus selected function from 6.
8. Negative Control
The negative control is used to minus selected function from 6.
9. Weld Process Selection Button
Press and release this button to change the selected weld process mode from mig to
tig to stick. The weld process will change to the next process in the sequence each time
the button is pressed and released. The green indicators next to the button will
illuminate to identify mig to tig to stick process mode.
10. 2T - 4T Trigger Latch Button
Press and release the button to change the selected operating mode of the trigger. The
selected mode can be either “2T” (unlatched) or “4T” (latched) operation. The green
indicator next to the button will illuminate to identify which mode is selected (2T or 4T).
In the 4T mode once the weld has been started you can release the trigger and
continue welding until the trigger is activated again or the welding arc is broken to stop
the welding arc.
11. 0.6/0.8/1.0/SPL
Press this button to choose the welding materials diameter, SPL is stainless steel.
12. MIG Torch Connecting
The MIG Torch Adapter is the connection point for the MIG Torch. Press the MIG Torch
in and secure by turning the locking ring to the right (clockwise)
13. Negative Welding Output Terminal
to the appropriate welding accessory such as the earth clamp (for Mig function) or
electrode holder (for Stick function). Negative welding current shows to the power
source via this heavy duty bayonet type terminal. It is essential, however, that the male
plug is inserted and turned securely to achieve a sound electrical connection.
14. Positive Welding Output Terminal
to the appropriate welding accessory such as the MIG Gun (via the MIG Gun polarity
lead) or ground clamp (for Stick function). Positive welding current flows from the
male plug is inserted and turned securely to achieve a sound electrical connection
.
6. Selecting function Button
Press and release this button to change the selected weld functions mode from welding
current to inductance to Volt to Burnback .
The negative welding terminal is used to connect the welding output of the power source
The positive welding terminal is used to connect the welding output of the power source
power source via this heavy duty bayonet type terminal. It is essential, however, that the
2.2 Layout For The Panel R231
44 55
33
11 11
15 15
16 16
22
11
10 10
66
12 12
14 14
13
13
99
88
77
DO NOT TOUCH the electrode wire while it is being fed through the system. The electrode
wire will be at welding voltage potential.
WARNING
1. Power Indicator
The green power indicator will be illuminated when the welder is turned ON and indicates
the presence of power.
3. JOB and SAVE
You can press JOB to select the memory records that you have saved before from 1-9.
For the new setting of present base current Amps ,just press SAVE.
2. Thermal Overload Indicator Light
This welding power source is protected by a self resetting thermostat. The indicator will
illuminate if the duty cycle of the power source has been exceeded. Should the thermal
overload indicator illuminate the output of the power source will be disabled. Once the
power source cools down this light will go OFF and the over temperature condition will
automatically reset. Note that the mains power switch should remain in the on position
such that the fan continues to operate thus allowing the unit to cool sufficiently. Do not
switch the unit off should a thermal overload condition be present.
4. Digital Ammeter
The digital meter is used to display the pre-set (preview) amperage in STICK / Mig modes
and actual welding amperage of the power source when welding, it is also used to
display parameters from selecting function button 6.