manualshive.com logo in svg

Vaisala RS41, Руководство пользователя

Поделиться
Скачать
Vaisala RS41 Скачать руководство пользователя страница 68

User’s Guide ______________________________________________________________________

66 ___________________________________________________________________M211486EN-A

Preparing the Radiosonde with 
Ground Equipment

1.

Start MW41 sounding software, if you have not started it yet, and 
log in.

2.

Attach the ozone destruction filter to the pump inlet tube.

3.

Place the RS41 radiosonde on the ground check device. The 
radiosonde is switched on when you place it on the ground check 
device. The message "Preparation in progress" will be displayed in 
MW41. 

4.

Before the preparation phase is completed, scroll the MW41 page 
down to the Special sensor window, and select 

Ozone

 from the 

drop-down list. 

5.

Fill in the information needed and click 

Apply

.

During this phase, the radiosonde LED light is red, but you can 
ignore it. It does not indicate an error at this point.

CAUTION

To be able to prepare an ozone sounding with MW41, you must import 
and activate the following scripts: 

OzoneCalculations.py

, 

OzoneMain.py

, and 

OIF411.py

. The scripts are included on the 

MW41 installation DVD, in folder ScriptLibrary\CalcOzone. The 
ozone sounding cannot be completed if any of these scripts is missing.

Import the scripts to the same Script Group and select OzoneMain.py 
as the main script. Make sure that Script group is set active. You do not 
need to set a command line argument. For more instructions, see 
MW41 on-line help.

CAUTION

Do not connect the Ozone Interface Board OIF411 to the radiosonde 
while the radiosonde is placed on the ground check device. Connecting 
OIF411 during the ground check will interrupt the preparations and 
MW41 will return to the Radiosonde selection window.

NOTE

The ASOPOS panel recommends 3.0 cm

3

 for cathode solution 

volume.

Содержание RS41





























































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды