Upright X Series Скачать руководство пользователя страница 38 | Manualshive

Страница: 38 / 164

background image

Page 3-10

Maintenance

3.8 - Motor Controller and I/O Board Dip Switch Settings

X Series Work Platform

3.8 M

OTOR

C

ONTROLLER

AND

I/O B

OARD

D

IP

S

WITCH

S

ETTINGS

NOTE:

Before the dip switch settings will take effect, power must be disconnected or Emergency Stop

Switches must be depressed.

C

ONTROLLER

Figure 3-12: Controller

The above table shows the default dip switch settings on
the controller box when the machine leaves the factory.
The following adjustments may be made to these set-
tings:

Switches 3 and 4 determine the elevated “creep” speed. If
the machine does not operate at the specified speed at the
default settings, use the following table to adjust the dip
switch settings

.

Switches 5 and 6 determine the deceleration time. Switch 5 is for the deceleration rate while the plat-
form is lowered. Switch 6 is for the elevated rate.

I/O B

OARD

Figure 3-13: I/O Board

The above table shows the default dip switch settings on the I/O
board when the machine leaves the factory. Switches 3 and 4
work together to determine the optional alarm settings

.

1

2

3

4

5

6

7

8

X20N

on

off

off

on

off

on

off

on

X20W

on

on

off

on

off

off

off

on

X26/31

on

on

off

on

off

off

off

on

3

4

1(slowest)

off

off

2

on

off

3 (default)

off

on

4 (fastest)

on

on

Decel

5

6

.24 sec.

off

off

1.27 sec.

on

on

1

2

3

4

X20N

off

off

off

off

X20W

off

off

off

off

X26/31

off

off

off

off

1

2

3

4

Result

on

Two Speed Mode (not used)

off

Proportional Control

on Not

used

off

Depression Mechanism extends

when platform is raised

off

off

Down alarm only

on

off

Down and Reverse alarm

off

on

Drive and Down alarm

on

on

All Motion alarm

1

2

3

4

8

7

6

5

1234

8765

1234

12

11

10

9

56

87

1234

12

11

10

9

56

87

1234

8765

4

3

2

1

Part

No.

Serial

No.

4

3

2

1

060571-005

«
...
36
37
38
39
40
...
»

Содержание X Series





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для X Series

ECL Comfort 110

Бренд: Danfoss Страницы: 8

Бренд: Danfoss Страницы: 16

Бренд: Miller Страницы: 16

SITALI CXOM 180

Бренд: Olimpia splendid Страницы: 32

7.4VOLT HEATED GLOVES

Бренд: Mobile Warming Страницы: 6

Бренд: M-system Страницы: 5

R1000 series E20

Бренд: Roland Страницы: 156

Бренд: Nedap Страницы: 5

Бренд: Leviton Страницы: 2

Бренд: WAGO Страницы: 12

ADAP-KOOL AK-SM 800

Бренд: Danfoss Страницы: 4

Бренд: Danfoss Страницы: 8

CompuScope 85GC

Бренд: Gage Страницы: 174

Бренд: Amplicon Liveline Страницы: 42

R7G4FML3-6-DA16

Бренд: M-system Страницы: 10

Бренд: Ravaglioli Страницы: 68

Бренд: Harmar Mobility Страницы: 16

Бренд: Brewtools Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды